研究者詳細 - 道木　慎二

論文 - 道木　慎二

分割表示 283 件中 21 - 40 件目／全件表示 >>

Active Damping Control Method for Different Dual-Parallel-SPMSM Systems with Single Inverter 査読有り国際誌 Open Access

Park, C; Doki, S

IEEJ JOURNAL OF INDUSTRY APPLICATIONS 12 巻 ( 1 ) 頁： 73 - 83 2023年

担当区分：最終著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：IEEJ Journal of Industry Applications

This paper presents a stabilization method for different dual parallel surface permanent magnet synchronous motor (SPMSM) systems with a single inverter. When a single inverter drives two synchronous motors, disturbance can cause a torque difference between the two motors. This can cause the motor’s electrical and mechanical resonance. Several damping control methods have been proposed to suppress such resonance. However, such methods consider that the parameters of the two motors are identical. When a single inverter controls two motors with different parameters, the damping control performance deteriorates. Besides, the motor’s resonance sound and current ripple increase. To address these problems, this paper proposes a control method for dual-parallel-SPMSM drive systems with a single inverter.

DOI： 10.1541/ieejjia.22006418

Extended EMF Observer of Dual Three-Phase Permanent Magnet Synchronous Motor Operable in Overmodulation Drive 査読有り国際誌

Imai, K; Doki, S; Kondo, K; Aoki, Y

IEEJ JOURNAL OF INDUSTRY APPLICATIONS 12 巻 ( 5 ) 頁： 901 - 913 2023年

記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：IEEJ Journal of Industry Applications

This paper proposes a novel extended electromotive force (EEMF) observer of a dual three-phase permanent magnet synchronous motor (DTP-PMSM) operable to the position sensorless overmodulation drive. The overmodulation drive occurs in current harmonics, and the estimated EEMF also contains harmonic components, leading to ripple error in the estimated position. Based on the vector space decomposition (VSD) utilized in DTP-PMSM current control, the proposed method can decrease the current harmonics in the overmodulation and the harmonic components in the estimated EEMF, and it can also improve position estimation. The effectiveness of the proposed EEMF observer and the improvement in the position estimation were experimentally verified.

DOI： 10.1541/ieejjia.22005441

Clustering Method of Driving Scenes based on Road Shape by using Road Map Images 査読有り国際誌

Hashimoto K., Yanagihara D., Kuniyuki H., Doki K., Funabora Y., Doki S.

4th International Conference on Electrical, Communication and Computer Engineering, ICECCE 2023 2023年

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：4th International Conference on Electrical, Communication and Computer Engineering, ICECCE 2023

Currently, vehicles are equipped with various sensors that can collect a series of driving behavior data while driving. The driving behavior data obtained in this way can be used to analyze the causes of traffic accidents and evaluate driver skills. However, when performing the above analysis, a specific driving scene is defined and driving behavior data for that driving scene is required. On the other hand, the series of driving behavior data obtained during one driving operation is enormous, and it is not easy to pick up desired driving scene data from among them. This research aims to establish a driving scene clustering method for a series of driving behavior data. In this paper, a driving scene is defined as a scene in which road shape and operation are associated, and propose a driving scene clustering method considered road shape. Here, a road map image is acquired from position information obtained from a GPS sensor, and the relationship between the road map image and operation data is clustered based on Coupled-GP-HSMM.

DOI： 10.1109/ICECCE61019.2023.10442604

Capacitor Current Reduction in Dual Three-Phase PMSM Drive System by Model Predictive Control Considering Dead Time 査読有り国際誌

Sakauchi R., Doki S., Imai K., Kondo K., Aoki Y.

2023 25th European Conference on Power Electronics and Applications, EPE 2023 ECCE Europe 2023年

担当区分：最終著者記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：2023 25th European Conference on Power Electronics and Applications, EPE 2023 ECCE Europe

This paper proposes a novel capacitor current reduction method in Dual Three-Phase PMSM Drive System. By using Model Predictive Control considering the dead time on the premise of implementation, the method modifies the three-phase voltage command generated by the PI current controller for the current reduction. The effectiveness is verified by simulation and experiment.

DOI： 10.23919/EPE23ECCEEurope58414.2023.10264351

Arm-Mounted Assistive Robot for Measuring Contact Force and Evaluating Wearer Safety 査読有り国際誌

Masaoka, S; Funabora, Y; Doki, S

IEEE ACCESS 11 巻頁： 114855 - 114863 2023年

担当区分：最終著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：IEEE Access

We developed a wearable assistive robot that directly measures the contact force acting between the robot and the human body, aiming to enhance the safety of such wearable devices. The force acting on the body is not directly measured, instead, it is estimated by measuring the torque acting on the robot joint in the wearable assistive robot. Despite the risk of failing to recognize dangerous forces due to modeling errors, the forces actually at work have not been examined. Here, we developed an arm-mounted assistive robot that directly measures the contact force as the distribution information to build a system and evaluate safety; in addition, the contact state between the robot and the human body was discussed. Accordingly, two experiments were conducted with 10 subjects. The first verified the contact force measurement performance of the robot, while the second demonstrated the application of contact force information to check the safety of the robot. The proposed robot can accurately measure the contact force, and the robot movement is safe under general control, for example, using the pain tolerance limit as the safety index. This eliminated the risk of not directly monitoring the forces acting on the surface of the human body. Furthermore, our result have implication for evaluating structural problems of the robot by evaluating contact conditions during movements.

DOI： 10.1109/ACCESS.2023.3324417

Application of Finite Control Set-Model Predictive Control for Servo Brake Motion in PMSM Drives 査読有り国際共著国際誌

Kawai, H; Cordier, J; Kennel, R; Doki, S

IEEE CANADIAN JOURNAL OF ELECTRICAL AND COMPUTER ENGINEERING 46 巻 ( 2 ) 頁： 117 - 129 2023年

担当区分：最終著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：IEEE Canadian Journal of Electrical and Computer Engineering

Finite control set-model predictive control (FCS-MPC) has a simple and intuitive optimization procedure. Therefore, FCS-MPC is increasingly being applied to control strategies for electrical drive systems. This article presents a method for servo brake control of a permanent magnet synchronous motor (PMSM) based on FCS-MPC. Accordingly, we propose a reference trajectory introduced in a cost function for brake motions and an alternating procedure with speed control. Moreover, this article clarifies the problem peculiar to servo-brake control using FCS-MPC, i.e., the reduction in tracking performance near the brake position because of the low resolution of the output voltage. In addition to the conventional method, a finite number of smoothed voltages were applied as candidate voltages for FCS-MPC to improve the tracking performance near the brake position. The smoothed voltages can effectively increase the resolution of the output voltage, which results in fewer steady-state errors in angular position tracking during servo brake motion. The simulation and experimental results obtained using a PMSM drive system reveal that the proposed strategy exhibited high performance in tracking the reference target during the operation of servobrakes and the ability to seamlessly alternate between servo brake and motor operations.

DOI： 10.1109/ICJECE.2022.3233029

Modeling of Novel Dual Three Phase PMSM with Pseudo-Triple Winding Structure and its Current Vector Control 査読有り国際誌

Aiba K., Doki S., Kato H., Isogai K.

2023 25th European Conference on Power Electronics and Applications, EPE 2023 ECCE Europe 2023年

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：2023 25th European Conference on Power Electronics and Applications, EPE 2023 ECCE Europe

In this paper, we propose the control model for a novel dual three-phase PMSM with pseudo-triple winding structure(DTP-PMSM with PTWS) which is one of the new multiple stator winding machines. The proposed control model is represented as the extended form of the conventional dual three-phase winding machine, and the validity is demonstrated by being compared with magnetic field analysis results. Furthermore, the current vector controller for the control model is designed and its performance is confirmed by simulation.

DOI： 10.23919/EPE23ECCEEurope58414.2023.10264324

Performance Evaluation of Position Sensorless Control System with Initial Speed Estimator for Overall Speed Startup 査読有り国際誌

Hao R., Doki S., Asahina K., Ide A.

2023 25th European Conference on Power Electronics and Applications, EPE 2023 ECCE Europe 2023年

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：2023 25th European Conference on Power Electronics and Applications, EPE 2023 ECCE Europe

Position sensorless control for Permanent-magnet synchronous motors has been investigated in numerous studies, but the issues of flying start at high speed are still a major problem. In our previous research, the issues on conventional position control are presented, and the reasons for these issues are distinguished as the initial response of the speed estimation. Based on this discussion, an initial speed estimation method is proposed as a solution. In this paper, the whole position sensorless control system with the initial speed estimation is presented, which enables the startup from overall speed, and the evaluation experiments are reported.

DOI： 10.23919/EPE23ECCEEurope58414.2023.10264244

Optimal Current Control Methods for Single-Inverter Dual-Parallel-SPMSM with Different Parameters 査読有り国際誌

Park, C; Doki, S

IEEJ JOURNAL OF INDUSTRY APPLICATIONS 12 巻 ( 5 ) 頁： 961 - 970 2023年

担当区分：最終著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：IEEJ Journal of Industry Applications

This paper presents optimal current-control methods for driving two different synchronous motors using a single inverter. When one inverter drives two motors, system efficiency will deteriorate if their loads are not identical. Moreover, even with identical loads, system efficiency will deteriorate if the parameters of the two motors are not identical. To address this issue, this paper proposes optimal current-control methods for systems with two different motors driven by a single inverter.

DOI： 10.1541/ieejjia.22010492

Optimal Current Control Methods for Dual-Parallel-SPMSM with Different Parameters Using a Single Inverter 査読有り国際誌

Park C., Doki S.

ICPE 2023-ECCE Asia - 11th International Conference on Power Electronics - ECCE Asia: Green World with Power Electronics 頁： 211 - 220 2023年

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：ICPE 2023-ECCE Asia - 11th International Conference on Power Electronics - ECCE Asia: Green World with Power Electronics

When one inverter drives both motors, the system efficiency deteriorates if both motors have different loads. Moreover, even if their loads are the same, the system efficiency would also deteriorate if the parameters of both motors are different. To address this issue, this paper proposes optimal current control methods for both different motors using a single inverter.

DOI： 10.23919/ICPE2023-ECCEAsia54778.2023.10213583

Position Sensorless Estimation for Surface Permanent Magnet Synchronous Motors Using Eddy Currents with Loads at a Low speed 査読有り国際誌

Miki Y., Tomita M., Hasegawa M., Doki S.

2023 International Future Energy Electronics Conference, IFEEC 2023 頁： 224 - 229 2023年

担当区分：最終著者記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：2023 International Future Energy Electronics Conference, IFEEC 2023

Position sensorless control of surface permanent magnet synchronous motors (SPMSMs) in low-speed regions is challenging because the motor has no magnetic saliency. Several methods using the block commutation drive technique to overcome this problem have been proposed; however, the rotor position is estimated only every 60° owing to the features of the block commutation drive method. Therefore, in this study, we proposed a novel sensorless rotor position estimation method by pasting the conductive nonmagnetic materials on the rotor. When high-frequency voltage is applied, eddy currents flow through the materials and the inductance slightly changes depending on the rotor position. In this study, estimating the continual rotor position from 0° to 360°, in which the sinusoidal vector control commutation is necessary rather than the block commutation drive method, was realized using these inductance changes. Based on the experimental results, we found that the rotor position could be continually estimated from 0 to 360°, which is necessary for sinusoidal vector commutation for an SPMSM with a position estimation error of approximately 6°, although the rotor velocity was low at 1.59 % of the rated velocity and 12 % of the rated load was applied.

DOI： 10.1109/IFEEC58486.2023.10458604

Turning a Functional Cloth Into an Actuator by Combining Thread-Like Thin Artificial Muscles and Embroidery Techniques 査読有り国際誌

Nakagawa, K; Sakai, Y; Funabora, Y; Doki, S

IEEE ROBOTICS AND AUTOMATION LETTERS 7 巻 ( 3 ) 頁： 5827 - 5833 2022年7月

担当区分：最終著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：IEEE Robotics and Automation Letters

In this letter, we propose to turn various existing cloths, especially functional cloths, into actuators by combined embroidery technology and thin McKibben artificial muscles. Most of the textile sensors so far are made by weaving active yarns into each other or into other base cloths. These devices have a limited choice of cloths that can be actuated. We create a prototypical actuator that can be deformed in three dimensions using thin artificial muscles and embroidery techniques on a functional cloth used for hook-and-loop fasteners and textiles that can observe pressure. Our experimental results indicate that the force of the artificial muscles can be transmitted to the cloth using fixation by embroidery and that the actuator can be variously deformed in three dimensions. We show that functional cloths can be made into actuators while maintaining their own functions using the proposed method.

DOI： 10.1109/LRA.2022.3157401

Basic Verification of Contact Force-Based Control with Full Body-Worn Assistive Robot 査読有り国際誌

Masaoka S., Funabora Y., Doki S.

2022 IEEE/SICE International Symposium on System Integration, SII 2022 頁： 144 - 149 2022年1月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：2022 IEEE/SICE International Symposium on System Integration, SII 2022

This paper evaluates the performance of contact force-based control with developed wearable assistive robots enabling the contact force measurement between the wearer and the robot. Almost all the conventional assistive robots are controlled with their joint torque measured via torque sensors. These robots have risks exerting excessive force on the wearer because torque sensors cannot detect contact force exerting the wearer. Our research group developed the contact force-based control and evaluated its performance only on the simulation. Also, we developed a prototype of a wearable robot enabling to measure and detect the contact force. In this paper, tracking performance to the wearer's movements, one of the basic performances of wearable robots, is confirmed via the experience. As a result, contact force-based control can operate in full accordance with the command of zero contact force.

DOI： 10.1109/SII52469.2022.9708851

Current Control System with High-Frequency Signal Injection for Dual Three-Phase Permanent Magnet Synchronous Motor 査読有り国際誌

Imai, K; Doki, S; Kondo, K; Aoki, Y

IEEJ JOURNAL OF INDUSTRY APPLICATIONS 11 巻 ( 1 ) 頁： 27 - 40 2022年

担当区分：最終著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：IEEJ Journal of Industry Applications

Dual three-phase permanent magnet synchronous motors have the characteristics of multi-phase and permanent magnet synchronous motors, whose double- and decoupled-winding models based on the vector space decomposition have been reported. High-frequency signal injection methods enable position sensorless control, parameter identification, and the search for maximum torque per ampere operating points. However, the current control system with high-frequency signal injection for a dual three-phase permanent magnet synchronous motor has not yet been sufficiently discussed. This study compares the double- and decoupled-winding models for the current control system with the high-frequency signal injection and proposes a current control system with high-frequency signal injection. Furthermore, this study proposes a position sensorless control method at low speed based on the high-frequency voltage injection as an application of the proposed current control system with the high-frequency signal injection. Experiments verify the effectiveness of the proposed current control system with the high-frequency signal injection and the proposed position sensorless control method.

DOI： 10.1541/ieejjia.20012955

AR Image Presentation based on Gaze Information for Operator support in teleoperation 査読有り国際誌

Doki K., Funabora Y., Doki S., Yano Y.

SAMI 2022 - IEEE 20th Jubilee World Symposium on Applied Machine Intelligence and Informatics, Proceedings 頁： 395 - 400 2022年

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：SAMI 2022 - IEEE 20th Jubilee World Symposium on Applied Machine Intelligence and Informatics, Proceedings

The authors have been tackling a new teleoperation system with a head-mounted display (HMD) and an omnidirectional camera to reduce the workload of an operator. Some experimental results verified that presentation of AR images based on sensor information could reduce the workload and prevent the deterioration of the task quality due to the transmission delay of images. However, the range of the field of view (FOV) of an HMD is narrower than that of a human. This difference might cause accidents by overlooking hazards that are outside the FOV of the HMD. To solve this problem, the authors propose a new method of AR image presentation based on gaze information not to overlook hazards. Some experimental results using a driving simulator verified the usefulness of the proposed method.

DOI： 10.1109/SAMI54271.2022.9780732

Operator Assistance for Remote Driving with Augmented Image based on Gaze Information 査読有り国際誌

Dokil K., Suzuki K., Funabora Y., Doki S., Yano Y.

IEEE International Symposium on Industrial Electronics 2022-June 巻頁： 1094 - 1099 2022年

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：IEEE International Symposium on Industrial Electronics

The authors have been aiming to realize a remote driving system with an HMD(Head Mounted Display) and a 360-degree camera to decrease the task load of the operator. Therefore, we have been tackling an operator assistance method of remote driving applying Augmented Reality(AR). In the previously proposed methods, AR video presented to the operator is generated based on sensing information of 3D LiDAR to deal with the communication delay. In this paper, a new generation method of AR image is proposed, in which Gaze information of the operator is used to create a 3D object to draw his attention to a hazard that might cause a traffic accident. The usefulness of the proposed method has been evaluated based on the results of the experiments using a driving simulator which has a scenario of a person jumping out from a park.

DOI： 10.1109/ISIE51582.2022.9831663

Motor Drive Method that Enlarges the Applied Voltage without Causing High Harmonics under the Voltage Supply Unbalance in Three Phase Dual Winding Permanent Magnet Motor 査読有り国際誌

Suzuki Takashi, Doki Shinji

IEEJ JOURNAL OF INDUSTRY APPLICATIONS 11 巻 ( 3 ) 頁： 506 - 513 2022年

担当区分：最終著者記述言語：英語掲載種別：研究論文（学術雑誌）出版者・発行元：IEEJ Journal of Industry Applications

To realize automated drive of a vehicle, more reliability to the motor drive system is required. The three phase dual winding permanent magnet motor drive using two inverters with corresponding voltage supplies is one of the potential candidates for the reliable motor drive system. With the respective voltage supply and winding connected to the inverter, the two motor drive systems are electrically independent. Thus, even if when a failure occurs in one of the systems, the other system can continue the motor drive. However, there is an issue: a voltage drop in one of the voltage supplies reduces the sinusoidal wave region of the drive system as the rotor of the motor is common in the two windings and the back electromotive voltage in the two windings are the same. The motor drive method that enlarges the applied voltage without causing high harmonics under the voltage supply unbalance in the three phase dual winding permanent magnet motor is proposed in this paper.

DOI： 10.1541/ieejjia.21009935

Implementation of Vector Control System On Multi-Core Processor by Using Model-Based Parallelization Tool 査読有り国際誌

Kim J., Sagae S., Edahiro M., Honda S., Doki S.

2022 International Power Electronics Conference, IPEC-Himeji 2022-ECCE Asia 頁： 1314 - 1319 2022年

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：2022 International Power Electronics Conference, IPEC-Himeji 2022-ECCE Asia

According to the increase in the required performance of the product, a multi-core processor that can process tasks simultaneously is attracting attention. To efficiently utilize a multi-core processor, a Model-Based Parallelization Tool(MBP) technology has been proposed to automatically generate paral-lelization code in consideration of the causal relationship of the control system. However, parallel processing time and control performance verification in real systems have not been sufficiently investigated. In this paper, to verify the validity of the parallelization code automatically generated by the MBP on a real system, we compare and review the single-code of the function unit by hand and the parallel code automatically generated by the MBP. In addition, we verify the MBP Tool by analyzing parallelization results as well as points to consider when implementing a motor control system.

DOI： 10.23919/IPEC-Himeji2022-ECCE53331.2022.9807202

Current Vector Control System Based on a New Discrete dq-Axis IM Model for High Speed Drive 査読有り国際誌

Takeuchi T., Doki S.

2022 International Power Electronics Conference, IPEC-Himeji 2022-ECCE Asia 頁： 783 - 788 2022年

担当区分：責任著者記述言語：日本語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：2022 International Power Electronics Conference, IPEC-Himeji 2022-ECCE Asia

In this paper, we propose a novel discrete current control scheme for IM (Inductive Motor). Ordinary, a current vector controller is designed by using the dq-axis model, which is induced under the assumption that Park transformation is continuously performed, and the designed controller is discretely implimented. If the sampling period is not short enough compared to the voltage supply frequency during high speed drive, these assumptions do not hold, and the control performance of the current system is greatly degraded, which results in control failure. To solve this problem, we proposed a discrete dq-axis IM model which is effective for low control period and high speed drive, and designed a current vector controller based on this model to improve control performance at high speed drive and confirmed the effect in simulation.

DOI： 10.23919/IPEC-Himeji2022-ECCE53331.2022.9807157

Performance Evaluation of Startup and Driving Strategy at Overall Speed with Extended ElectroMotive Force for Position Sensorless Permanent Magnet Synchronous Motor 査読有り国際誌

Hao R., Kozakura T., Doki S.

2022 International Power Electronics Conference, IPEC-Himeji 2022-ECCE Asia 頁： 362 - 367 2022年

担当区分：責任著者記述言語：日本語掲載種別：研究論文（国際会議プロシーディングス）出版者・発行元：2022 International Power Electronics Conference, IPEC-Himeji 2022-ECCE Asia

Extended electro-motive force (EEMF) estimation method is a fast position estimation method used for overall speed. In our previous research, we have reported the startup and drive method with EEMF from standstill. However, starting a free-running PMSM, which is known as the flying start, is rarely taken into consideration in the most position sensorless research. Under such condition, the rotor speed is unobservable before the startup. In this paper, a startup and driving strategy at overall speed with EEMF by speed and signal injection is proposed, and the evaluation experiments are reported.

DOI： 10.23919/IPEC-Himeji2022-ECCE53331.2022.9806847

　前のページ - 次のページ　

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15