Language：English   Publishing type：Research paper (scientific journal)   Publisher：Applied Thermal Engineering  

Crude oil fouling is described as an accumulation of unwanted materials such as asphaltene and metallic salt on a heat transfer surface in a pre-heat train of the crude distillation unit in oil refineries, causing an economic loss of 1–1.2 billion U.S. dollars per year in 2019. Computational fluid dynamics is one of the useful simulation tools for numerical research on this topic. However, crude oil fouling is a long-term phenomenon; therefore, the time scale is longer than general computational fluid dynamics problems. The fouling layer in oil refineries grows over several months to several years despite the small pipe diameter of several or several tens of millimetres. For this reason, it is not easy to satisfy the Courant–Friedrichs–Lewy condition. To overcome this problem, we developed a new algorithm based on a weak coupling approach, validated this scheme, and exhibited the application of this technology. In the new algorithm, momentum and pressure fields and enthalpy and mass fraction fields are solved separately. The algorithm was implemented as FoulingFOAM, a crude oil fouling simulator based on OpenFOAM v2006. Then, the solver was first validated with the lab-scale measurements, showing good agreement with the experimental data. Next, industrial-scale data in the two refineries were simulated for validation. It was possible to predict the peak fouling resistance against time. Finally, for both lab- and industrial-scale simulations, the predictions of our numerical tool showed that fouling resistance increased with higher wall temperature, lower crude oil velocity, and higher concentration of fouling species, which were identical to previous measurements. Hence, we concluded that the weak coupling approach is promising for investigating crude oil fouling problems.

DOI： 10.1016/j.applthermaleng.2024.124614

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Industrial and Engineering Chemistry Research  

Liquid hydrogen (LH2) presents a viable solution for energy storage and transportation, particularly when produced by using renewable electricity. In this study, the energy efficiency of large-scale PEM water electrolysis for hydrogen production was investigated to be 59.74%, with the levelized electricity cost of hydrogen of 57.48 kWh/kg. To recover the waste heat from the PEM electrolyzer, two heat integration approaches have been proposed: the organic Rankine cycle (ORC) and the absorption refrigeration cycle (ARC). The ORC converted waste heat into electricity, while the ARC generated cold energy to precool the refrigerant, alongside electricity generation, both of which reduced energy consumption in the hydrogen liquefaction process. Subsequently, the process parameters were optimized through Matlab with the Mesh Adaptive Direct Search algorithm aimed at minimizing the specific energy consumption (SEC) of hydrogen liquefaction integrated with ORC or ARC, resulting in SECs of 6.76 and 6.61 kWh/kg LH2, with 21.33% and 22.87% reductions compared with the liquefaction process without heat recovery, respectively. The corresponding exergy efficiencies were 56.96% and 57.16% for the liquid hydrogen production process, with 86.69% and 87.73% for the hydrogen liquefaction process, respectively.

DOI： 10.1021/acs.iecr.4c02383

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Chemical Engineering Science  

Absorption using an amine solvent is one of the primary means for capturing CO2 from many combustion sources such as fossil fuel power plants. CO2 capture systems by absorption need a large amount of thermal energy to strip CO2 from the amine solvent. In recent years, absorption using a phase separation solvent, which forms two phases when CO2 is absorbed, has been demonstrated as a promising technique to reduce the energy consumption. In this study, we examine several process models for the CO2 absorption process using a phase separation solvent, and quantify the uncertainty of the model parameters. We estimated model parameters, including equilibrium and mass transfer parameters, from two sources of experimental data: solubility tests, as well as lab-scale absorber tests. Model parameters were estimated by Bayesian inference using the Markov chain Monte Carlo method. The proposed approach successfully quantified the uncertainties of the model parameters.

DOI： 10.1016/j.ces.2024.120348

Web of Science

Scopus

Authorship：Corresponding author   Language：English   Publishing type：Research paper (scientific journal)   Publisher：Energy and Fuels  

To achieve energy-environment synergy and sustainability, this study proposes a poly generation system that integrates the energy release process of liquefied natural gas (LNG) oxy-fuel power generation with the energy storage process of green methanol synthesis from renewable energy. In this system, oxygen, the byproduct of water hydrolysis to hydrogen, can support LNG oxy-fuel power generation; while the cold energy released during LNG regasification can serve as a cold source for carbon capture, the captured CO2 can be utilized as the carbon source for methanol synthesis, thus realizing cleaner methanol production and an efficient power generation process with near-zero carbon emission. Following the process design, the parameters were optimized with minimum levelized production cost of methanol and electricity as the objective function through Matlab using the “MADS” algorithm, resulting in 683.79 $/tonne and 68.05 $/MW h, respectively, with overall exergy efficiency of 50.28%. Notably, as green methanol synthesis requires additional CO2, a reduction of 2272.59 kg/h can be achieved. The study concludes that the novel poly generation process is superior in exergy efficiency and CO2 capture and utilization but inferior in high production costs.

DOI： 10.1021/acs.energyfuels.4c01250

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Waste Management  

Poly(vinyl chloride) (PVC) is one of the most widely used plastics. However, a major challenge in recycling PVC is that there is no economical method to separate and remove its toxic phthalate plasticizers. This research made a breakthrough by extracting PVC with liquefied dimethyl ether (DME) and successfully separating the plasticizer components. Nearly all (97.1 %) of the di(2-ethylhexyl) phthalate plasticizer was extracted within 30 min by passing liquefied DME (285 g) through PVC at 25 °C. The compatibility of PVC with organic solvents, including liquefied DME, was derived theoretically from their Hansen solubility parameters (HSP), and actual dissolution experiments were conducted to determine the optimal PVC solvents. A liquefied DME mixture was used to dissolve PVC, and the extract was diluted with ethanol to precipitate the dissolved PVC. We demonstrated that liquefied DME is a promising method for producing high quality recycled products and that the process retains the fundamental properties of plasticizers and PVC without inducing degradation or depolymerization. Because of its low boiling point, DME can be easily separated from the solute after extraction, allowing for efficient reuse of the solvent, extracted plasticizer, and PVC. DME does not require heat and produces little harmful wastewater, which significantly reduces the energy consumption of the plasticizer additive separation process.

DOI： 10.1016/j.wasman.2024.04.050

Web of Science

Scopus

PubMed

Language：English   Publishing type：Research paper (scientific journal)   Publisher：International Journal of Greenhouse Gas Control  

This study focuses on optimizing the energy requirement in the post-combustion CO2 capture system using pressure swing regeneration through a model-based design (MBD). The simulation results highlight the significant impact of CO2 recovery, inlet gas and liquid flow rate, and CO2 concentration in the flue gas on the overall energy demand of the system. Moreover, an investigation into the de-sublimation chamber was undertaken, revealing a relationship between dry ice formation and the heat transfer between the LNG stream and CO2 in the heat exchanger. The parametric analysis study reveals that the sensible heat of the lean solvent is significantly influenced by the CO2 concentration in the liquid, consequently affecting the overall system energy. According to the results, the utilization of cold energy from LNG could save 80 % of the total energy requirement. The optimization results found the best working condition, which consumes energy of 0.190 GJ/ton CO2, 31 % lower than the basic scenario.

DOI： 10.1016/j.ijggc.2024.104154

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Industrial and Engineering Chemistry Research  

CO2 solubility is one of the key factors in evaluating not only the efficiency of the absorbent but also the energy consumption of the CO2 capture process from flue gas. In this study, a system namely headspace gas chromatography (HS-GC), which is a combination of gas chromatography (GC-3200, GL Sciences) and a headspace autosampler (Turbomatrix HS16, PerkinElmer), was developed to measure the CO2 solubility of amine solutions. The equilibrium time and calibration curve of this system were checked and compared with those of the literature data. The developed system showed high reproducibility with reference CO2 solubility data of benchmark amine solutions. Distinct from conventional measurement methods of CO2 solubility, high-throughput CO2 solubility measurement by HS-GC shows its advantages such as a small amount sample requirement, rapid achievement of equilibration time, automation of sample exchange, and high reproducibility, which is superior in the amine solvent screening phase. Moreover, this system can evaluate new types of CO2 capture solvents, including the phase separation solvent. By acquiring continuous data, the inflection point in the solubility curve indicated by phase separation was observed. The absorption heat estimated from those CO2 solubility curves measured by this system also agrees well with the experimental data.

DOI： 10.1021/acs.iecr.3c03314

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：International Journal of Hydrogen Energy  

During the design of the carbon capture and hydrogen storage process, a static CO2 hydrogenation poly-generation process for methanol and formic acid synthesis was developed, thereby reducing recycling flow and feedstock losses in the single methanol synthesis process and increasing product diversity. Additionally, a novel flexible poly-generation process was proposed as the product prices fluctuated with the market environment throughout the plant's life cycle. For the static poly-generation process, a mixed integer nonlinear programming model was established, followed by the Mesh Adaptive Direct Search algorithm to determine the optimal parameter design. For flexible processes, with the unscented transform tool, a two-stage optimization strategy is proposed for obtaining optimal design and operating parameters that are computationally tractable. With an input CO2 flow rate of 200 kmol/h, the results show (1) the static process with an optimal Return On Investment of 13.05%, a fixed investment cost of $ 34.14 × 106, and an annual net profit of 4.46 × 106 $/year; and (2) the flexible process, in which the flexibility indices of the methanol and formic acid production units are 1.088 and 1.194, respectively, resulting the fixed investment cost increase to $ 39.19 × 106, an increase of 14.79%. Accordingly, the annual net profit increased by 8.97% to 4.86 × 106 $/year, while the Return On Investment decreased by 4.67%–12.44%. For investment decision-makers, the flexible poly-generation process can achieve higher profits and reduce potential market risks when they have adequate financing.

DOI： 10.1016/j.ijhydene.2023.01.205

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Carbon Resources Conversion  

The concentration of the major greenhouse gas CO2 is rapidly increasing in the atmosphere, leading to global warming and a range of environmental issues. An efficient circulation and utilization of CO2 is critical in the current environmental context. Methanation, an exothermic process, emerges as a critical strategy for effective CO2 utilization. On this front, there is a significant demand for rational design of catalysts that maintain high activity and methane selectivity over a wide temperature range (250–550 °C). The catalyst that can promise a consistent reaction even at 500 °C under an atmospheric pressure is thus obliged. The present study investigated bimetallic catalysts with SiC, which is known for its exceptional thermal conductivity, and CeO2, which is characterized by its CO₂ affinity, as base materials. We incorporated Ni-M and Ru-M (M = Co and Mn) as the active metals, each loaded at 2 %. Impressively, with merely 20 mg, the Ni-Co/SiC catalyst achieved a CO2 conversion rate of 77 % and CH₄ selectivity of 88 % at 500 °C, in a fixed-bed tubular reactor system with conditions of H2/CO2 = 4, a total flow rate of 70 ml min−1, and a steady GHSV of 12,000 h−1. Moreover, 2Ni-2Co/CeO2 catalyst demonstrated exceptional performance with a 76 % conversion of CO2 and a 83 % selectivity for CH4, all under identical conditions. The catalyst's durability was confirmed by a subsequent 40-hour stability test, which showed only a 3–5 % degradation. The developed catalysts were comprehensively characterized by BET/BJH, CO pulse chemisorption, H2-TPR, HAADF-STEM-EDS, SEM-EDS and XRD etc. to unveil their physicochemical and surface traits. It was found that Co and Mn, when integrated, effectively restrained the agglomeration of Ni and Ru particles, ensuring optimal metal dispersion on the support. In conclusion, our synthesized bimetallic catalysts shown a sustained catalytic capability, even in the high-temperature environment.

DOI： 10.1016/j.crcon.2024.100241

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Fuel  

This paper reports a computational fluid dynamics simulation of carbon dioxide (CO2) methanation via the Sabatier process in a shell-and-tube reactor, incorporating a water phase change simulation on the shell side using the volume of fluid (VOF) method. The essential heat removal factors and their mechanisms, such as the catalyst size, bed porosity, thermal conductivity, coolant flow rate, and coolant boiling, were primarily investigated. The computational code was a newly developed in-house version of ChtMultiRegionFOAM based on OpenFOAM v2006. This code can simulate catalyst-gas heat transfer, which is called the two-temperature model. The code was extended to new methanation and phase-change models based on the VOF method. The computational code was first validated using existing experimental data. After sufficient accuracy was confirmed, several parametric studies were conducted. Catalyst heat conductivity was the most influential factor among the catalyst-related parameters. The flow rate of the oil coolant significantly affected the cooling performance. Finally, the use of boiling water significantly reduced the coolant flow rate. Moreover, the cooling performance remained unchanged until the total heat release rate from the gas exceeded the total latent heat of the water.

DOI： 10.1016/j.fuel.2023.128126

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Fuel  

The injection of CO2 with coal into coal gasifier is a promising approach to achieve CO2 recirculation. Predicting the formation and evolution of polycyclic aromatic hydrocarbons (PAHs) and soot during coal gasification is particularly important as their presence poses challenges to the gasifier operation and environment. However, the effect of CO2 injection on their formation must be elucidated in more detail to optimize the gasifier design. This work investigates PAHs and soot formations in gas-phase reactions under different gasifying agents (Air, O2/CO2, O2/H2O) in a two-stage entrained flow coal gasifier using a detailed chemical kinetic model (DCKM). Under the O2/CO2– and O2/H2O-blown conditions, aromatics reforming was progressed whereas the yields of tar and soot were effectively suppressed. The benzene was observed as the most abundant PAHs species, followed by naphthalene and acenaphthalene. Regarding the relative oxygen concentration, the conversion behavior of aromatics was significantly influenced in the O2/CO2-blown condition, while the somewhat effect was found in the O2/H2O-blown condition. Tar yield peaked at 50% relative oxygen concentration in the O2/CO2-blown condition. The present finding may have practical significance in the O2/CO2-blown gasifier to facilitate CO2 recirculation for the oxy-fuel IGCC system.

DOI： 10.1016/j.fuel.2023.127876

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Heliyon  

In this study, we report on a computational fluid dynamics (CFD) simulation of the chemical vapor deposition reactor of silicon carbide (SiC) in the methyltrichlorosilane (MTS, CH3SiCl3)/H2 system. The formation of SiC thin film is controlled by various process parameters, such as temperature and pressure. In this study, we propose a reaction mechanism of MTS decomposition to SiC growth on a substrate surface for CVD reactors in the CH3SiCl3(MTS)/H2 system. The reaction mechanism has two gas-phase pyrolysis reactions and one SiC film formation reaction. However, we individually build and validate MTS decomposition and SiC growth models to reduce uncertainty. An in-house version of reactingFoam, a reactive flow solver within OpenFOAM v2006, was used as the simulation tool. Our model accurately reproduced MTS decomposition for T = 1100–1350 K and [H2]/[MTS] = 2.65–14 at p = 101,325 Pa. Then, the MTS decomposition model was coupled with the SiC growth model, and the coupled model was applied to the SiC deposition data. The model could reproduce multiple datasets through validation studies.

DOI： 10.1016/j.heliyon.2023.e15061

Web of Science

Scopus

PubMed

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Chemical Engineering Science  

Dry reforming of methane (DRM) is one of the feasible strategies for carbon capture and utilization. However, the DRM process has a high tendency toward carbon deposition, which is restricted to industrial applications. In order to further improve coke formation resistance, open-cell foam with hierarchical pore structure was investigated. An artificial algorithm was adopted to construct a hierarchical pore structure in open-cell foam. Based on a 3-D lattice Boltzmann model, this work explored the effect of two hierarchical pore structure parameters on the fluid flow and coke formation characteristics in open-cell foam, which are hierarchical pore volume ratio (V2/V1) and hierarchical pore size ratio (d2/d1). The results indicated that increasing V2/V1 and d2/d1 can significantly promote permeability. Under the restriction ofV2/V1 = 4, from d2/d1 = 1 to 4, the coke formation rate decreases by approximately 57.49 %. These findings provide a theoretical basis and technical guidance for designing and developing open-cell foam reactors.

DOI： 10.1016/j.ces.2022.118380

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Applied Thermal Engineering  

Effective thermal conductivity in open-cell foam with hierarchical pore structure was estimated using lattice Boltzmann method. A new structure algorithm was proposed to reconstruct hierarchical pore structure in open-cell foam. In order to elucidate the heat transfer characteristics in hierarchical pore structure, the effect of structure parameters, namely the hierarchical pore size ratio (d2/d1), the hierarchical pore volume ratio (V2/V1), and temperature on the effective thermal conductivity was investigated. These results indicated that hierarchical pore structure is unfavorable to the effective thermal conductivity in open-cell foam for the heat conduction process. At high temperatures (Tave = 450–1650 K), however, the effective thermal conductivity in hierarchical pore structure is higher than that in uniform pore structure considering heat radiation. Furthermore, for the heat conduction process, a correlation of the effective thermal conductivity related to open-cell foam with hierarchical pore structure was proposed and validated by available experimental data.

DOI： 10.1016/j.applthermaleng.2022.119314

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Journal of Advanced Manufacturing and Processing  

CO2 methanation, which converts CO2 and hydrogen into methane as fuel, is one of the promising candidates for the development of CO2 utilization technologies. Recently, a highly active catalyst made of Ni/ZrO2 for methanation has been developed, and is currently investigated as a potential use in a high-performance reactor. However, design of reactor must be carried out carefully, since this reaction is highly exothermic, which may cause reactor runaway and deterioration of catalysts. For this problem, a mathematical model that can predict the behavior inside the reactor is necessary. In this work, we consider the methanation reaction of CO2 in a reactor model and estimate the kinetic parameters in the reaction rate model from experimental data. In the parameter estimation using literature values and Tikhonov regularization, eight kinetic parameters in the rate equations were identified from 64 data points with a wide range of conditions. We confirm that molar fractions at the reactor exit predicted by this reactor model are in good agreement with the experimental results. Furthermore, the developed model was validated to predict the compositions and temperature that were not used in the estimation. We expect the developed model will be a powerful tool for the reactor design.

DOI： 10.1002/amp2.10145

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：ISIJ International  

Researchers have thoroughly studied coal pyrolysis over a long period, while the analysis of volatile evolution and the chemical structural changes of solid char were carried out individually in most of the studies. In this work, we quantified the chemical reactions to explain the different physical phenomena, such as softening and caking properties, exhibited by different ranks of coals during pyrolysis. Four typical carbonaceous feedstocks (bituminous, sub-bituminous, lignite coals, and biomass) were selected as test samples. The authors analyzed the generated gas during pyrolysis by using a quadrupole mass spectrometer (Q-MS) and the chemical structure of the pyrolyzed char via spectroscopic methods (NMR, FT-IR, CHNS, and XPS) to gain new insights into the pyrolysis mechanism of the carbonaceous feedstocks. Transferable hydrogen was introduced to define the hydrogen used to stable the free radicals formed during pyrolysis, which can be obtained by quantifying the conversion routes of hydrogen. The hydrogen released for the growth of aromatic clusters has three pathways, namely, (1) consumption by the hydrodeoxygenation reaction to produce pyrolytic vapor, (2) release as gaseous H2, and (3) transferable hydrogen. The calculation shows that the amount of transferable hydrogen during pyrolysis decreases as the coal rank gets lower. For pyrolysis up to 500°C, the amount of transferable hydrogen is 3.96, 2.32, and 1.36 mol/kg-coal for bituminous, sub-bituminous, and lignite coals, respectively. On the other hand, the transferable hydrogen of biomass needs to be further considered in terms of the effect of cellulose and hemicellulose’s structure.

DOI： 10.2355/isijinternational.ISIJINT-2022-517

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Journal of Analytical and Applied Pyrolysis  

Lignin is one of the most promising biopolymers for producing hydrocarbons and aromatic compounds in nature. Electrochemical conversion of lignin is regarded as an attractive technology for producing various aromatic chemicals which are generally derived from fossil fuels. The author reports an electrochemical approach for hydrogenating alkaline lignin (AL), which uses relatively low-cost Ni foam as a working electrode under alkali electrolyte. The primary factors (such as power input, reactor type, temperature, reaction time, catalysts, and electrode substrates) of electrochemical hydrogenation were used to control the products' yield and features. The redox characteristics of the reaction system were directly compared with the cyclic voltammetry measurement under different parameters. After electrochemical hydrogenation (ECH), rapid pyrolysis was conducted on HAL samples to investigate the influence of electrochemical reactions on lignin. The maximum olefins and aromatics yield from HAL was increased to more than three times AL, accounting for 2.22 wt% and 4.07 wt%, respectively. Then, thermogravimetric analysis (TGA), elemental analysis (EA), Fourier-transform infrared spectroscopy (FTIR), and heteronuclear single quantum coherence (HSQC) NMR were employed to characterize hydrogenated lignin samples (HAL), as well as gas chromatography–mass spectrometry (GC-MS) was conducted to investigate the oil-phase products. This work focused on this electrochemical hydrogenation coupled with rapid pyrolysis process to give a possibility that converting lignin into not only liquid oil products, but solid hydrogenated lignin can be used to produce more olefins and aromatics in rapid pyrolysis, and presented the advantages and disadvantages of this two-stage process finally.

DOI： 10.1016/j.jaap.2022.105625

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：ACS Applied Energy Materials  

Electrochemical reduction of CO2comprising the CO2reduction reactuib (CO2RR) and oxygen evolution reaction (OER) is one of the most promising technologies for electrification of the chemical process industry. Here, the performance of a electrocatalyst with a three-dimensional structure of InZnCu on Cu foam (CF) is presented. This electrocatalyst was fabricated by electrodeposition of In and Zn over Cu and exhibited a superior reduction of CO2to CO at a Faradaic efficiency of 93.7% at -0.7 V and an excellently long duration of 100 h. Due to the synergy of the thin In layer, the Zn nanosheets provided a high surface-active area and strong mechanical robustness during the reaction. Additionally, a two-electrode system was constructed based on the CF-modified surface, which provided valuable guidelines on the overall CO2RR-OER system for further evolution. Furthermore, due to the facile synthesis, the bimetal-layer double hydroxide (LDH) exhibited high conductivity and high OER performance. Hence, the two-electrode system assembled excellent electrocatalysts for the CO2RR-OER (InZnCu/CF||Cu(OH)2NWs@NiCo-LDH/CF) with high conversions of CO2to CO of 67% and 88% at 2 and 50 mA cm-2, respectively. Notably, the CO2RR-OER system exhibited excellent stability in a 40 h CO2conversion with a constant current density of 2 mA cm-2at an ultralow voltage of 1.59 V. Moreover, the calculation of the energy input converting CO per ton of CO2resulted in a low energy input range for further development in scalability. This overall CO2RR-OER proposes development in electrochemical CO2reduction for industrial applications.

DOI： 10.1021/acsaem.2c01564

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Energy Conversion and Management  

In order to upgrade biomass-derived platform chemicals to high value-added chemicals and liquid fuels, it is highly advantageous and desirable to synthesize suitable non-precious bimetallic catalysts that are efficient and versatile in chemical reactions. Equal moles of Ni and Cu were dispersed on varying mole ratios of Al by the co-precipitation method to synthesize Ni-Cu alloy particles to obtain a maximum yield of tetrahydrofurfuryl alcohol (THFA) by the liquid phase hydrogenation of furfural. The nickel species were active for both the furan ring (C=C) and carbonyl group (C=O) of furfural molecule, while Cu species were highly active for only the carbonyl group of furfural molecule. Systematic characterization of the prepared catalysts by XRD, TPR, STEM-EDS, and XPS analysis revealed the formation of highly active Ni-Cu alloys and near-equal Ni/Cu surface contents were achieved for the equimolar catalyst, which showcased a maximum of 98 mol% yield of THFA at 140 °C, 30 bar, 4 h. The reaction pressure and temperature showed a substantial effect on the product yield. The solvent selection also influenced the product selectivity, particularly with 2-butanol, which promoted the reaction with its hydrogen donor capacity and supported the ring hydrogenation of FAL to THFA. Moreover, the reduced Ni1Cu1-Al1 catalyst displayed good recyclability for three runs and an equal activity to that of a fresh catalyst after the regeneration.

DOI： 10.1016/j.enconman.2022.115736

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Journal of Molecular Liquids  

The multi-conformational structures sampling of a molecule, considered as conformational information, is found to be crucial for applying COSMO-SAC to systems containing compounds with flexible molecular structures, such as alkylene glycol derivatives. In this study, a hybrid modeling approach that combines the COSMO-SAC model with classical molecular dynamics (MD) is proposed to investigate the phase behavior of systems containing alkylene glycol derivatives. The accuracy in predicting liquid–liquid equilibrium (LLE) was found to be strongly influenced by conformational populations obtaining from MD simulations under different solvation environments. The overall root mean square deviation (RMSD) in predicting LLE mutual solubility from COSMO-SAC for seven selected mixtures containing alkylene glycol derivatives reduces from 19.1% to 10.1% when conformation distribution is included. The new approach significantly improves the accuracy in predicting phase behaviors for alkylene glycol derivatives solutions and can be applied to systems containing compounds with flexible molecular structures.

DOI： 10.1016/j.molliq.2022.118896

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Journal of the Taiwan Institute of Chemical Engineers  

Background: Phase separation solvents are proposed to replace conventional solvents for CO2 capture due to a significant reduction of absorbent regeneration heat. A predictive approach based on COSMO-SAC is developed to model the CO2 capture process using the phase separation solvent of 2-(ethylamino)ethanol (EAE) + water + diethylene glycol diethyl ether (DEGDEE). Methods: In this approach, liquid phase compositions, including CO2 solubility, are determined from vapor-liquid-liquid equilibrium calculation with a chemisorption reaction in both liquid phases. The behavior of phase separation after CO2 capture and CO2 solubility in both CO2-lean and CO2-rich phases at 313 and 353 K can be well described by the proposed approach. Significant findings: The overall root-mean-square-deviation (RMSD) in predicting compositions (128 data points) of all components in both liquid phases is 0.064, which is slightly better than a previous study on the accuracy of COSMO-SAC in LLE prediction (RMSD = 0.105). The phase separation behavior of solvent can be realized with the hydrophilic product upon CO2 absorption from the σ-profile analysis. The proposed framework is expected to be a useful tool for the development of a new phase separation solvent.

DOI： 10.1016/j.jtice.2022.104362

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：International Journal of Hydrogen Energy  

The Sabatier process is a competitive technology applied for carbon capture and utilization. This process increases the risk of carbon deposition and catalyst thermal degradation because of its exothermic property. In this study, a CFD model verified through existing experimental data was established to systematically investigate the Sabatier process in a shell-and-tube reactor. The effects arising from several operating parameters (e.g., gas flow rate, feed gas composition, the thermal conductivity of catalyst pellet, the inlet temperature of cooling phase, as well as phase change refrigeration) on temperature profile and reaction performance were studied. Moreover, a mechanism of three reactions was investigated, including CO2 methanation, CO methanation, as well as RWGS reaction. Furthermore, the competition between CO2 methanation and RWGS reaction was explored. According to the further sensitivity analysis, increasing the thermal conductivity of the catalyst particles would be effective to inhibit hot spots, while keeping the carbon conversion rate unchanged.

DOI： 10.1016/j.ijhydene.2022.03.029

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1016/j.jtice.2021.11.010

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Fuel Processing Technology  

Major global issues such as greenhouse gas emissions and the excessive use of fossil fuels lead to looking for sustainable and clean energy resources. Lignocellulosic biomass is a prospective resource for sustainable carbon-based energy. The production of petroleum-based green fuels, chemicals, and solvents from biomass-derived products has garnered much attention in the recent past. The study of biomass derivatives hydrogenation improves the efficiency of generating high-value chemicals and provides much-needed insights into the primary reaction mechanism for the effective utilization of raw constituents or biomass. However, the existing thermochemical conversions of biomass and biomass-derived products such as thermal catalytic hydrogenation (TCH) involve energy-intensive and expensive processes. In this regard, sustainable energy generation attracts alternative conversion technologies, including electrochemical conversion (ECC), electrocatalytic hydrogenation (ECH), and photocatalytic conversions that can be directly integrated with renewable wind/solar technologies and operated at ambient or lower temperatures. The role of electrocatalyst and electrolyte is pivotal to achieve efficient and selective ECH of biomass organics. This review paper summarizes the utilization of TCH and ECH processes on cellulose/hemicellulose, lignin, and their derivatives/model compounds, including catalyst types, reaction conditions, hydrogenation efficiency, and technical limitations. The advantages and disadvantages of the two technologies for biomass utilization have also been compared, which provides a more favourable knowledge base and theoretical basis for the subsequent research work.

DOI： 10.1016/j.fuproc.2021.107097

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：International Journal of Greenhouse Gas Control  

Durability and fire hazard risk evaluations were conducted to determine the process feasibility of a unique phase separation solvent with a low regeneration temperature (90 °C) consisting of an amine, ether, and a small amount of water. The results are as follows. I) The amine degradation rate of the phase separation solvent was determined to be less than 1/10 of that of monoethanolamine, which was attributed to the high oxidative resistance and low regeneration temperature of the former. II) The composition of the gas that formed in the absorber was completely out of the combustible range during the treatment of 6% oxygen-containing gas on a dry basis. Therefore, we believe that this phase separation solvent is applicable to the treatment of exhaust gas from coal-fired thermal power plants and can realize stable operation with a small amount of amine required for replenishment.

DOI： 10.1016/j.ijggc.2021.103532

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Journal of Molecular Liquids  

We studied local structure of diethylene glycol diethyl ether (DEGDEE)-water mixtures near the lower critical solution temperature (LCST) by means of simultaneous small- and wide-angle x-ray scattering measurement and thermodynamic calculation based on the activity coefficient model. Long-wavelength limits of structure factors SNN(0), SCC(0), and SNC(0), which respectively represent mean square fluctuations in the particle number, the concentration, and their cross correlation, are determined from scattering intensity extrapolated to the zero scattering vector and thermodynamic quantities according to the Bhatia and Thornton formula. SNN(0) and SCC(0) exhibit maxima near critical concentration. We found that difference between partial molar volumes of water and DEGDEE essentially results in SNN(0) values being one order of magnitude larger than SCC(0) values. Further, we determined Kirkwood-Buff (KB) integrals to clarify a mixing state of the solution from a mesoscopic point of view. The KB integrals also exhibit extrema near critical concentration. These results demonstrate self-segregations of both DEGDEE and water in a nanometer length scale even at homogeneous solution states, which can be regarded as a precursor of the macroscopic phase separation. Concentration dependence of the wide-angle scattering curve suggests that the short-range structure, whose length scale is sub-nanometer, moderately changes between the intrinsic bulk structures of DEGDEE and water. Comparison of the KB integrals with those determined by the activity coefficient model using non-random two-liquid equation is presented and effects of the fluctuation on the phase behavior are discussed.

DOI： 10.1016/j.molliq.2021.117830

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Energy and Fuels  

Methanation of CO2 using H2 obtained by renewable energy sources has been gaining attention as one of the promising options for utilizing captured CO2 and surplus power obtained when intermittent power sources such as solar and wind energy are used. Herein, kinetics of CO2 methanation over Ni/ZrO2 was studied using a tubular quartz reactor at 0.9 MPa. The Sabatier reaction (CO2 + 4H2 = CH4 + 2H2O, ΔHr298K = – 165 kJ mol–1) was carried out under stoichiometric gas feeding (CO2/H2 = 1/4 v/v to CH4/H2O = 1/2 v/v), and its reaction rate was determined. The exothermic nature of CO2 methanation and extremely high catalytic activities increased the reaction temperature to 400–600 °C even when the feed-gas temperature was as low as 250–400 °C, and the gas hourly space velocity was as high as 3 × 106 h–1. Nonlinear regression analyses based on one- and multistep kinetic models were used to investigate the reaction rates to estimate the kinetic parameters. Both models with optimized parameters can reproduce the experimentally obtained CH4 formation rates for the entire range of the feed-gas conversion with a coefficient of determination (R2) of over 0.98.

DOI： 10.1021/acs.energyfuels.1c01534

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：ACS Sustainable Chemistry and Engineering  

This paper presents an alternative concept of CO2 capture that can substantially reduce the energy required for CO2 capture by utilizing unused cold energy. The heat of vaporization of liquefied natural gas (LNG), of which the boiling point is 110 K, is a possible candidate for unused cold energy. This technology is based on a pressure swing amine process combined with a sublimation tank to cool CO2 released from a desorber into dry ice by exchanging the LNG cold energy. The feature of this technology is that pure CO2 is recovered mostly by a pressure swing that decreases the pressure in the desorber utilizing a cryogenic pump with CO2 sublimation instead of a mechanical pump. We developed an amine-based absorbent that can realize the proposed process for exhaust gas from a fossil fuel-fired power plant. A process simulation indicated that the required energy is as low as 0.25 GJ/ton CO2 when both the absorber and the desorber are operated at around 313 K, the desorber pressure is reduced to 1 kPa, and the sublimation tank is operated at 150 K.

DOI： 10.1021/acssuschemeng.1c05892

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：AIChE Journal  

The Sabatier process is promising for carbon dioxide utilization and energy storage. However, the serious problem that limits more comprehensive industrial applications is catalyst deactivation due to the temperature runaway phenomenon. The inert particle dilution approach, including the mixing dilution method and layered dilution method is applied to solve this problem. Based on the lattice kinetic scheme-lattice Boltzmann method (LKS-LBM), the effects of three parameters in bed dilution structure reconstructed by the discrete element method (DEM) on temperature distribution and carbon conversion rate were discussed, so as to investigate the relationship between packing structure and temperature distribution. Furthermore, numerical results indicated that an optimal bed dilution structure, which not only can control the peak temperature below the critical temperature to avoid coking and sintering of catalyst, but also can improve the conversion rate by almost 18% compared with the structure without dilution under the same circumstance.

DOI： 10.1002/aic.17304

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Journal of Molecular Liquids  

There is a growing interest in developing CO2 capture processes based on phase separation solvents due to its much lower energy consumption compared to the reference amine process using monoethanolamine (MEA). In this work, the predictive COSMO-SAC activity coefficient model was applied to describe phase behavior for phase separation solvent composed of amine + water + glycol ether. From the calculated ternary liquid-liquid equilibrium (LLE) phase diagram, ternary mixtures of fourteen selected amines + water + glycol ether can be classified into miscible- or immiscible-type solvents. The work presented here indicates that amines having comparable affinity to water and glycol ether generally result in a smaller two-phase region and form type I phase behavior near the amine-lean region. The amines having a strong affinity to water or glycol ether show a larger two-phase region and result in type II phase behavior. Further analysis shows that KOW and σ-profile can be good indicators for the affinity of amine to water and glycol ether, which is the key factor to determine the phase behavior of investigated ternary mixtures. The feed composition and operating temperature of phase separation solvent should be judged by the interaction between solvent molecules. This study demonstrates that COSMO-SAC is a useful tool for exploiting the phase behavior of potential phase separation solvents with limited available experimental data.

DOI： 10.1016/j.molliq.2021.116229

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Journal of Chemical and Engineering Data  

Viscosity and density of amine absorbents affect directly their flow, which is involved in the process design and simulation of carbon dioxide capture. A mixture of 2-(ethyl amino) ethanol (EAE), diethylene glycol diethyl ether (DEGDEE), and water changes its phase from homogeneous to two-liquid ones on CO2 absorption. It is difficult to calculate the viscosity and density of this phase separation solution, especially those of quaternary-component phases. In this research, models to calculate the density and viscosity of the quaternary-component system of EAE/DEGDEE/water/carbamate were suggested based on nonrandom two-liquid (NRTL)-DVOL and NRTL-DVIS models. Given the component concentrations, these models can replicate well the viscosity and density of the solutions. A good calculation result with a few numbers of parameters makes the models simple and easy to use.

DOI： 10.1021/acs.jced.1c00195

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Journal of Analytical and Applied Pyrolysis  

Valorization and utilization of lignin have been drawing increasing attention recently. Hydroprocess is one of the main technologies, which can reduce organic compounds and partially depolymerize the macromolecular structure of lignin. The mechanism of lignin hydroprocess has been extensively discussed focusing on hydrogenolysis. In contrast, the solid residue regarded as unreacted or depolymerized lignin has drawn less attention so far. This study proposes an integrated process that consists of catalytic hydrogenation and subsequent fast pyrolysis for valorizing lignin. The results showed that 48−87 wt.% of solid product could be recovered as hydrogenated lignin (H-EOL) after hydrogenation at 200–250 ℃ for 1−7 h. Chemical structure of H-EOL was comprehensively investigated by means of elemental analysis, FTIR, 13C & 1H NMR, and TGA. Furthermore, behavior of fast pyrolysis of H-EOL was detected here for the first time. H-EOL has higher hydrogen to carbon atomic effective ratio(H/Ceff ratio) and achieves the increasing reactivity of thermal decomposition. H-EOL yields light olefins double as much as raw ethanol organosolv lignin (EOL). And the formation of alkanes (C1-C4), benzene, and toluene was promoted to various degrees, while the yield of carbon monoxide, carbon dioxide, and vapor decreased. A novel and efficient pretreatment method has been provided to valorize lignin, which is instructive for subsequent research.

DOI： 10.1016/j.jaap.2021.105096

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Journal of Chemical Engineering of Japan  

An approach in predicting reactions undergone by coal volatiles in a reducing section (reductor) of an air-blown two-stage entrained flow gasifier toward designing a better gasification process was proposed. A detailed chemical kinetic model was applied to simulate chemical reactions of a complex molecular mixture of the coal volatiles evolved due to rapid pyrolysis of coal fed into the reductor. The composition of volatiles was determined based on pyrolysis-gas chromatography experiments, where 22 compounds, including inorganic gases (H2, H2O, CO and CO2), light hydrocarbon gases (C1–C4), and aromatic hydrocarbons (benzene to pyrene) were identified. Gas composition at the reductor inlet was estimated by integrating the information on the experimentally obtained molecular composition of the volatiles, and the thermodynamically calculated composition of inorganic gases generated from the combustor and the coal feeding rates into reductor and combustor. Concentration profiles of the individual chemical species, as well as soot particles together with the flow direction of the reductor, were revealed using an extended detailed chemical kinetic model involving 202 species, 1351 gas-phase reactions, and 101 surface reactions for soot formation and growth. The simulation revealed that near-complete decomposition of tar regarded as a set of all aromatic hydrocarbons is likely to require operation temperature of the reductor at temperatures as high as 1200°C, when the combustor is operated at 1800°C.

DOI： 10.1252/jcej.20we171

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Energy and Fuels  

This review presents the recent advances in computational approaches to understand thermochemical reactions of solid fuels with minimized empirical factors. It includes studies on kinetic modeling of gas-phase reactions of multicomponent molecular mixtures of volatiles derived from primary pyrolysis of solid fuels using a database for elementary reactions. Mechanistic studies to model the devolatilization of biomass and coal upon heating are also mentioned. The efforts to integrate the kinetic model with computational fluid dynamics to understand the flow and heat transfer behavior of industrial reactors for solid fuel conversions, including gasification and combustion, are reviewed. These advances are primarily based on the conventional forward analysis that provides a deeper understanding of chemically reacting flows of fuels undergoing thermochemical reactions. For the further development of the thermochemical conversion technology, it can be expected to develop alternative approaches such as inverse analysis to determine the optimal reactor design and operating conditions.

DOI： 10.1021/acs.energyfuels.0c04052

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1016/j.ces.2020.116105

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Carbon Resources Conversion  

The current state of lignin has been characterized by these three: (1) as one of the main components in lignocellulosic biomass with an abundant amount; (2) not be taken seriously but treated as a waste product; (3) underutilized due to a complex and stubborn structure. However, lignin can be a rich source for hydrocarbons and aromatic compounds when gives appropriate utilization. In this work, we have studied the hydrotreatment of alkaline lignin (AL) under relatively mild conditions and further investigated the characterization of hydrogenated lignin (HL), especially the behavior during fast pyrolysis. The recovery of the HL decreased with increasing reaction temperature from 60 wt.% to 41 wt.% in the range of 150–250 ℃. The hydrotreated products were analyzed using Elemental Analysis, FTIR (for HL) and GC–MS (for bio-oil). The HL samples were found to have a higher hydrogen/carbon atomic effective ratio (H/Ceff ratio) and a higher degree of saturation than AL. Compared to the internal structure of the lignin before and after hydrotreatment, the side chain groups were removed from AL during the process. After that, from the fast pyrolysis of HL, it was observed that more light hydrocarbons and aromatic compounds were formed than that of AL. Furthermore, fast pyrolysis in the hydrogen atmosphere revealed that more volatile fractions were released compared to the Helium atmosphere. The total olefins yield was increased for HL compared AL from 1.02 wt.% to 3.1 wt.% at 250 ℃ for 7 hours. This study of HL is instructive to some extent for the industrial utilization of lignin.

DOI： 10.1016/j.crcon.2021.09.001

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：Carbon Resources Conversion  

This work presents the formation of butyl levulinate, a potential fuel additive, and an excellent renewable chemical obtained by the butanolysis of furfuryl alcohol (FAL) over a solid acid catalyst. The butanolysis of furfuryl alcohol reaction is a strong function of acidity for which tungstated zirconia (WO3-ZrO2), a robust solid acid catalyst, and a sulfonated carbon catalyst were employed to produce high yields of butyl levulinate targeting a lower initial molar ratio of butanol to FAL. A maximum of 28 mol% yield of butyl levulinate was obtained with tungstated zirconia catalyst. Easily prepared sulfonated carbon catalyst at high reaction temperatures facilitated the complete conversion of reaction intermediate, 2-butoxymethylfuran (2-BMF) through which butyl levulinate was formed, and as high as 80 mol% of butyl levulinate yield was produced at an initial mole ratio of 8.5:1 of butanol to FAL. The better results of sulfonated carbon catalyst could be attributed to the presence of -SO3H, carboxylic acid, and phenolic OH groups on the carbon surface.

DOI： 10.1016/j.crcon.2021.03.003

Web of Science

Scopus

Language：Japanese   Publishing type：Research paper (scientific journal)   Publisher：Proceedings of the International Conference on Power Engineering 2021, ICOPE 2021  

We suggest new CO2 absorption processes with biphasic phase separation type for reducing consumption energy. the CO2-rich solution liquid was separated hydrophilic liquid and hydrophobic liquid. In this work, we studied some kind of amine and ether mixture solvents, and observed phase separation phenomena. From the results of phase separation characteristics, we selected with 2-Amino-2-methyl-1-prophanol (AMP), diethylene diethyl ether (DEGDEE) and water pair. We measured the CO2 solubility at different temperature and CO2 patricidal pressure conditions, and evaluated the effect of component concentration in the solvents on CO2 absorption characteristics and phase separation phenomena. We adjusted the biphasic solvents. AMP, DEGDEE and H2O of biphasic solvent weight-composition ratio are 30, 20 and 50 wt% respectively. The CO2 solubility of absorption at 40 ℃, 0.1atm was obtained 0.647 mol-CO2/mol-AMINE. The CO2 solubility of desorption at 90℃, 1.0 atm was obtained 0.177 mol-CO2/mol-AMINE. The difference of CO2 loading of this solvent was high performance of CO2 capture compared with that of other solvents. These result is attributed to the additive phase assisting in the regeneration of CO2 by extracting the regenerated amine. The results of the present study show reduction of desorption temperature and high CO2 absorption performance.

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：15th Greenhouse Gas Control Technologies Conference 2021, GHGT 2021  

We calculated the energy required for regeneration when the phase separation solvent solvent is applied to the treatment of exhaust gas from coal-fired power plants. This solvent is characterized by regeneration at a low temperature of less than 100°C. As a result, it was clarified that under ideal conditions with no pressure drop and no heat loss, the required energy could be suppressed to 1.5 GJ/ton-CO2 by satisfying the following conditions; i) pinch point of the heat exchanger between rich-amine and lean-amine: 1 °C, ii) water concentration of the solvent: kept at 10 wt%, iii) COP of the heat pump: 5.5. However, increase of the pinch point, increase of the water concentration, and decrease of the COP will all result in a significant increase in the required energy. Therefore, in order to realize a process with low energy consumption, it is essential to meet these design constraints.

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：15th Greenhouse Gas Control Technologies Conference 2021, GHGT 2021  

Durability and fire hazard risk evaluation were conducted to determine the process feasibility on the unique phase separation solvent with low regeneration temperature (90 °C), consisting of amine, ether, and small amount of water. The results we obtained are as follows; I) The amine degradation rate of the phase separation solvent would be less than 1/10 of that of monoethanolamine (MEA), which was contributed by its high oxidative resistant nature and low regeneration temperature. II) The gas composition formed in the absorber was completely out of combustible range and almost no accumulations of explosive compounds such as peroxides were observed when in contact with 6 % oxygen containing gas (dry base). Therefore, we believe that the phase separation solvent is applicable to the treatment of exhaust gas from coal-fired thermal power plants.

Scopus

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1021/acs.iecr.0c03233

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1002/amp2.10067

Scopus

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1021/acssuschemeng.0c02459

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1021/acs.iecr.9b04672

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1016/j.ces.2019.115276

Scopus

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1002/amp2.10033

Scopus

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1016/j.molliq.2019.111411

Scopus

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.2355/isijinternational.ISIJINT-2018-816

Web of Science

Scopus

Language：Japanese   Publishing type：Research paper (scientific journal)   Publisher：36th Annual International Pittsburgh Coal Conference: Clean Coal-Based Energy/Fuels and the Environment, PCC 2019  

Scopus

Language：Japanese   Publishing type：Research paper (scientific journal)   Publisher：36th Annual International Pittsburgh Coal Conference: Clean Coal-Based Energy/Fuels and the Environment, PCC 2019  

Scopus

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1016/j.ijggc.2018.05.010

Web of Science

Scopus

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1021/acs.jpcb.8b00946

Web of Science

Language：English   Publishing type：Research paper (scientific journal)   Publisher：GHGT 2018 - 14th International Conference on Greenhouse Gas Control Technologies  

The unique phase separation type amine/ether absorbent is expected to realize the CO2 separation process with low-energy consumption (1.5GJ/ton-CO2). In this study, a degradation test of the absorbent under thermal load of liquid regeneration was conducted in order to clarify 1) the behavior of its performance declination for CO2 capture and 2) the behavior of amine loss mainly caused by generation of by-product. The regeneration condition was chosen based on two assumptions that a) most likely to damage to the solution, which means high-oxidation atmosphere containing oxygen and sulfur oxide, and b) adopting actual operating temperature when absorbing or desorbing. As a result, only a small amount of the CO2 capture capability was lost through 48 hours cyclic thermal load of 50-90 °C. Consequently, it was found that the phase separation type solvent could be durable enough for the practical use. Besides, the running cost associated with make-up amine might be drastically reduced.

Scopus

Language：English   Publishing type：Research paper (scientific journal)   Publisher：GHGT 2018 - 14th International Conference on Greenhouse Gas Control Technologies  

We have developed the phase separation solvent for CO2 capture. Our developed solvent consists amine, organic solvent and water and shows single liquid phase before CO2 absorption though it shows two liquid phases after CO2 absorption. Feature of phase separation solvent is reducing temperature difference between absorber and stripper. We apply the heat pump system for CO2 separation and evaluate the energy consumption. Low temperature swing process saves energy requirement for CO2 capture process with highly-effective reaction-heat recovering. To evaluate the CO2 capture system with our solvent, screening test for amine and organic solvent combination and CO2 solubility measurement were examined. In the phase separation test, three types of solvents were obtained by combining amine and ether, that is, no phase separation with CO2 scrubbing, phase separation with CO2 scrubbing, and thoroughly immiscible. The phase behaviour depends on the hydrophobicity of amines or organic solvents, and the types of solvents were classified using the hydrophobic parameter.

Scopus

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1016/j.jct2017.05.043

Web of Science

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1252/kakoronbunshu.43.342

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.3775/jie.96.339

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1016/j.egypro.2017.03.1224

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1252/kakoronbunshu.43.342

Web of Science

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.3775/jie.96.386

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

Language：English   Publishing type：Research paper (scientific journal)  

Language：English   Publishing type：Research paper (scientific journal)  

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1016/j.supflu.2011.04.016

Language：English   Publishing type：Research paper (scientific journal)  

Language：English   Publishing type：Research paper (scientific journal)  

DOI： 10.1016/j.supflu.2011.08.003,

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

Language：English   Publishing type：Research paper (scientific journal)  

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

Authorship：Lead author   Language：English   Publishing type：Research paper (scientific journal)  

Language：Japanese

Language：Japanese

Language：Japanese

Language：Japanese

Event date： 2023.11

Language：Japanese   Presentation type：Oral presentation (invited, special)  

Venue：早稲田大学リサーチイノベーションセンター   Country：Japan  

Event date： 2023.5

Language：Japanese   Presentation type：Oral presentation (invited, special)  

Venue：名古屋大学 野依記念学術交流館   Country：Japan  

Event date： 2023.4

Language：Japanese   Presentation type：Oral presentation (invited, special)  

Venue：東京 新お茶の水連合会館   Country：Japan  

Event date： 2023.2

Presentation type：Symposium, workshop panel (nominated)  

Event date： 2022.9

Presentation type：Symposium, workshop panel (public)  

Country：Japan  

Event date： 2022.6

Presentation type：Public lecture, seminar, tutorial, course, or other speech  

Country：Japan  

Event date： 2022.2

Presentation type：Oral presentation (invited, special)  

Event date： 2021.12

Presentation type：Public lecture, seminar, tutorial, course, or other speech  

Event date： 2021.11

Language：Japanese   Presentation type：Oral presentation (invited, special)  

Event date： 2021.10

Presentation type：Oral presentation (general)  

Event date： 2021.9

Presentation type：Oral presentation (general)  

Event date： 2021.8

Presentation type：Oral presentation (invited, special)  

Event date： 2021.6 - 2021.7

Presentation type：Oral presentation (invited, special)  

Event date： 2021.2

Event date： 2020.12

Event date： 2020.10

Event date： 2019.10

Event date： 2019

Language：English   Presentation type：Oral presentation (general)  

Scopus

Event date： 2019

Language：English   Presentation type：Oral presentation (general)  

Scopus

Event date： 2017.11

Language：English   Presentation type：Oral presentation (general)  

Country：Japan  

Event date： 2017.9

Language：English   Presentation type：Oral presentation (general)  

Country：Japan  

Event date： 2017.9

Language：English   Presentation type：Oral presentation (general)  

Venue： Beijing   Country：Japan  

Event date： 2017.9

Language：English   Presentation type：Oral presentation (general)  

Country：Japan  

Event date： 2017.8

Language：English   Presentation type：Oral presentation (general)  

Venue：Hong Kong   Country：Japan  

Event date： 2017.6

Language：Japanese   Presentation type：Oral presentation (general)  

Country：Japan  

Event date： 2017.5

Language：Japanese   Presentation type：Oral presentation (general)  

Venue：明治大学理工学部 生田キャンパス   Country：Japan  

Event date： 2016.11

Language：English   Presentation type：Oral presentation (general)  

Country：United States  

Event date： 2016.11

Language：English   Presentation type：Oral presentation (general)  

Country：Switzerland  

Event date： 2016.10

Language：English   Presentation type：Poster presentation  

Venue：Pacifico YOKOHAMA Annex Hall   Country：Japan  

Event date： 2016.9

Language：Japanese   Presentation type：Poster presentation  

Country：Japan  

Event date： 2016.5

Language：Japanese   Presentation type：Oral presentation (general)  

Venue：日本大学生産工学部津田沼キャンパス   Country：Japan  

Event date： 2016.5

Language：Japanese   Presentation type：Oral presentation (general)  

Country：Japan  

Event date： 2015.5

Language：Japanese   Presentation type：Oral presentation (general)  

Country：Japan  

Event date： 2015.5

Language：Japanese   Presentation type：Poster presentation  

Country：Japan  

Event date： 2014.7

Language：English   Presentation type：Poster presentation  

Country：Japan  

Event date： 2014.5

Language：Japanese   Presentation type：Poster presentation  

Country：Japan  

Event date： 2014.5

Language：Japanese   Presentation type：Poster presentation  

Country：Japan  

Event date： 2013.12

Language：English   Presentation type：Poster presentation  

Country：Japan  

Event date： 2012.9

Language：English   Presentation type：Oral presentation (general)  

Country：Japan  

Event date： 2012.9

Language：Japanese   Presentation type：Oral presentation (general)  

Country：Japan