担当区分：筆頭著者,　責任著者   記述言語：英語   掲載種別：研究論文（学術雑誌）  

DOI： https://doi.org/10.1016/j.colsurfa.2023.133113

記述言語：英語   掲載種別：研究論文（学術雑誌）   出版者・発行元：International Communications in Heat and Mass Transfer  

Adsorption heat transformer (AHT) cycles, unlike adsorption cooling cycles, upgrade the heat source to a higher temperature. Despite the renewed interest in the AHT cycles, its performance enhancement schemes along with their impacts are yet to be explored extensively. Heat and mass recovery schemes on the adsorption cooling/heating cycles have been extensively studied. However, AHT cycles are fundamentally different from those cycles since the AHT cycles employ isothermal-adiabtic processes. Thus, similar impacts of the heat and mass recovery scheme as in the cooling/heating cycles cannot be expected in AHT cycles. Therefore, the impacts and limitations of the internal heat recovery scheme on the AHT cycle are investigated in the current study. The heat recovery scheme aims to minimize the requisite uptake consumption for preheating the adsorber bed by recovering the sensible heat between two adsorber beds having different temperatures. This sensible heat exchange is modeled using modified energy-balance equations to capture the non-linearity of the adsorption process. The preheating uptake loss decreases from 0.014 kg/kg to 0.007 kg/kg at the heat source-heat supply temperature combination of 60 °C–80 °C due to the maximum possible heat recovery in the AHT cycle. As a result of the reduced preheating uptake loss, approximately 5% and 10% increase in the useful heat ratio and exergy efficiency of the AHT cycle, respectively are obtained. This modified AHT cycle further improves the performance ratio of the hybrid AHT-MED (multi-effect distillation) system from 4.6 to 4.9 at the heat source temperature of 58 °C. Furthermore, a parametric analysis of the cycle's performance metrics has been conducted for various degrees of heat recovery, representing the effect of realistic heat exchanger effectiveness during the recovery process. This study will help propel the theoretical development of the adsorption-based thermodynamic systems.

DOI： 10.1016/j.icheatmasstransfer.2023.106774

Web of Science

Scopus

記述言語：英語   掲載種別：研究論文（学術雑誌）  

Adsorption heat transformers (AHTs) are considered as promising systems for upgrading waste heat to a higher temperature. The cycle operates among three temperature reservoirs: (i) heat sink at the low temperature (TL), (ii) heat source at the medium temperature (TM), and (iii) heat supply at the high temperature (TH). In the present study, the performance the AHT cycle was analyzed for possible applications in the waste heat upgrade and thermal desalination. An equilibrium model was developed using adsorption characteristics and isotherm data. Five types of commercially available silica gels and three types of zeolites were investigated as adsorbents. Nonlinear optimization technique was utilized for the determination of the intermediate pressure and uptake for preheating and precooling phase of the AHT cycle. The performance parameters in terms of useful heat ratio and condensation heat ratio were determined and compared for the reservoir temperatures at 30 °C (TL)—60 °C (TM)—80 °C (TH). Parametric evaluation of the performance parameters was carried out based on the variation in gross temperature lift, as well as the heat exchanger mass ratio. It was found out that reduction in the gross temperature lift had a positive impact on the useful heat ratio and a negative influence on the condensation heat ratio of the AHT cycle. Significant variations in the maximum adsorption capacity and slope of the isosteric heat of adsorption across various adsorption pairs containing zeolites were observed. As a result, AQSOA-Z01 zeolite exhibited the highest heat exchange values of the AHT cycle in the range of ~ 320–370 kJ per kg of adsorbent. On the contrary, type AQSOA-Z02 zeolite displayed the lowest corresponding values in the range of ~ 60–90 kJ kg-1 of adsorbent. On the other hand, variation across the different silica gel adsorbents was comparatively smaller because of similar isotherm and isosteric heat of adsorption characteristics. This study will assist the research on the theoretical development of the AHT cycle via material selection and system design optimization.

DOI： 10.1007/s10973-022-11350-3

Scopus

記述言語：英語   掲載種別：研究論文（学術雑誌）  

Adsorption process can be initiated either by Large Temperature Jump (LTJ) or Large Pressure Jump (LPJ). In this study, a theoretical analysis of coupled heat and mass transfer process during LPJ driven adsorption has been carried out using scaling principles of the governing conservation equations. A columnar domain consisting of silica gel (adsorbent) and water vapour (adsorbate) pair has been considered with heat and mass transfer directions orthogonal to each other. This domain is subjected to a sudden LPJ with isothermal boundary condition. Adsorption process has been divided into three phases for scaling analysis viz. i) pressure equalization ii) adsorption accompanied by heat generation and iii) heat removal phase. From order of magnitude arguments, various important physical scales for each phase have been derived and validated with a 2-dimensional computational fluid dynamics (CFD) study. The temperature rise in the adsorber bed is found to be 14.5 K, and the time scale to attain peak temperature is ~100 s from the initiation of adsorption. This justifies the short cycle time deployed in practical PSA systems to operate near isothermal condition. The outcomes of this investigation serve as a fundamental insight into LPJ driven adsorption process and help identify the various factors which practically effect this mode of adsorption.

DOI： 10.1016/j.icheatmasstransfer.2022.106101

Scopus

記述言語：英語   掲載種別：研究論文（学術雑誌）  

Multi-effect distillation (MED) systems are considered to be the most energy-efficient thermal desalination methods. This paper introduces the development of a novel thermal desalination system for performance superior to MED systems for the same operating temperature limits. Such an unprecedented achievement was attained by upgrading the heat source using the chemical potential of adsorption phenomena. The proposed Adsorption Heat Transformer (AHT) cycle hybridized with Multi-effect distillation system (AHT-MED) exhibits higher performance ratio and water production rate than a conventional MED system for the same heating source and sink. The heat generated by the heat of adsorption with the temperature higher than the heat source is supplied to the first effect of the MED system, thus, extending the temperature difference between the Top Brine Temperature (TBT) and Bottom Brine Temperature (BBT). The higher temperature difference offers more number of effects, with the equivalent temperature difference between the effects (ΔTe) as the design parameter. Using the low-temperature heat source (as low as 58 °C), the system can employ an increased number of effects (as high as 11) due to the supply of heat at an increased temperature of around 80 °C. The proposed system achieves a higher performance ratio (approximately 5.4) and water production rate (2 kg/s) compared to the standalone MED system (PR: 4.2, WPR: 1 kg/s) with the number of effects of the hybrid system as 10 at constant interstage temperature difference between the standalone and hybrid systems. This novel AHT-MED system opens up new possibilities for low-temperature heat source-driven thermal desalination with significantly improved performance.

DOI： 10.1016/j.apenergy.2021.117744

Scopus

会議種別：口頭発表（一般）  

記述言語：英語   会議種別：口頭発表（一般）  

会議種別：ポスター発表  

会議種別：口頭発表（一般）  

会議種別：口頭発表（一般）