Faculty Profiles - NAKAMURA Maki

Papers - NAKAMURA Maki

Division display >> ／ All the affair displays 1 - 35 of about 35

6-2-2　Study on methane synthesis process using treated gas from automobile shredder dust as feedstock Reviewed

Nakamura Maki, Li Qiao, Chopendra G. Wasnik, Norinaga Koyo

Proceedings of the Annual Conference of The Japan Institute of Energy Vol. 33 ( 0 ) page： 162 - 163 2024.7

Language：Japanese Publishing type：Research paper (scientific journal) Publisher：The Japan Institute of Energy

This study proposes a rational process aimed at carbon recycling to effectively recycle carbon dioxide (CO2) emitted from automobile shredder residue (ASR). The methods investigated include direct methane synthesis from ASR process gas and methane synthesis from CO2 recovered by chemical absorption using a gas engine cogeneration system. By optimizing the type and operating conditions of these reactors, it was found that the methane synthesis cost can be reduced by using CO2 recovered through chemical absorption in the methane synthesis process.

DOI： 10.20550/jietaikaiyoushi.33.0_162

CiNii Research

6-2-3　Development Of CO2 Methanation Catalysts Supported On CeO2 And SiC At Elevated Temperatures Reviewed

Chopendra G. Wasnik, Nakamura Maki, Shimada Taiki, Machida Hiroshi, Norinaga Koyo

Proceedings of the Annual Conference of The Japan Institute of Energy Vol. 33 ( 0 ) page： 164 - 165 2024.7

Language：English Publishing type：Research paper (scientific journal) Publisher：The Japan Institute of Energy

The increasing concentration of CO2 in the atmosphere is a major environmental concern, and effective utilization of CO2 is crucial. In this context, efficient circulation and utilization of CO2 are paramount. The methanation process emerges as a critical strategy for effective CO2 utilization. The methanation is an exothermic reaction. Therefore, catalysts that uphold high activity and methane selectivity over a wide temperature range are in significant demand. This study investigated 2Ni-2Co/SiC and 2Ni-2Co/CeO2 bimetallic catalysts, using only 20 mg of the sample. The experiments were carried out in a fixed-bed tubular reactor at a steady GHSV of 12,000 h-1. The results showed that the catalyst 2Ni-2Co/SiC showed 77% conversion of CO2 with an 88% CH4 selectivity, while 2Ni-2Co/CeO2 demonstrated 76% CO2 conversion and 83% selectivity for CH4 at 500°C. These bimetallic catalysts have high activity for Ni and Ru, with resistance to Co and Mn carbon deposition, and can withstand high temperatures up to 500°C without losing activity, selectivity, and thermal stability. The catalysts were characterized through multiple tests, to unveil their physicochemical properties. The Co and Mn have effectively restrained the Ni and Ru agglomeration, optimized metal dispersion, and enhanced catalytic activity even in high-temperature environments.

DOI： 10.20550/jietaikaiyoushi.33.0_164

CiNii Research

CO2 methanation over Ni-M, Ru-M (M= Co, Mn) catalysts supported on CeO2 and SiC Reviewed

Chopendra G. Wasnik, Maki Nakamura, Shimada Taiki, Machida Hiroshi, Koyo Norinaga

Carbon Resources Conversion 2024.4

Fabrication and Evaluation of Particulate Matter Purification Filter Using Plasma-Sprayed Catalyst Film on SUS316 Mesh Reviewed

Maki NAKAMURA, Takaharu MINAMI and Masakuni OZAWA

J. Jpn. Soc. Powder Powder Metallurgy 2024.3

Fabrication and Evaluation of Particulate Matter Purification Filter Using Plasma-Sprayed Catalyst Film on SUS316 Mesh Invited Reviewed

Maki Nakamura, Takaharu Minami, Masakuni Ozawa

Materials Transactions 2024

1-02　Tar and soot formation characteristics of various coals in a two-stage entrained flow coal gasifier revealed by detailed chemical kinetic modeling Reviewed

LI Tailin, NAKAMURA Maiki, UEHARA Yusuke, MACHIDA Hiroshi, NORINAGA Koyo

Proceedings of Conference on Coal Science Vol. 60 ( 0 ) page： 4 - 5 2023.10

Language：Japanese Publishing type：Research paper (scientific journal) Publisher：The Japan Institute of Energy

Substituting air with either CO2 or H2O in the gasifying agents presents a viable strategy for promptly integrating a carbon-neutral energy vector into coal gasification technology, concurrently mitigating harmful particulate matter emissions. However, fully understanding the evolution of tar in the practical gasifier has proven to be challenging owing to complex mixture of the scale of reactors. This study presents a detailed kinetic investigation of tar and soot formations from the gas-phase reactions in the reductor of a two-stage entrained flow coal gasifier under oxy-fuel (O2/CO2, O2/H2O) atmospheres. The effects of temperature and coal types were studied. The results show that benzene, followed by naphthalene and phenanthrene, serves as the primary tar products. Higher temperature promotes tar reduction, especially under O2/H2O condition. Moreover, soot yield under the O2/H2O condition is less than that under the O2/CO2 condition owing to weaker hydrogen abstraction acetylene addition route. Soot yield decreases with the temperature rises. This work provides valuable insights and guidance for the reduction of tar and soot in the two-stage entrained flow coal gasifier under oxy-fuel atmospheres.

DOI： 10.20550/jiesekitanronbun.60.0_4

CiNii Research

1-08　The computational fluid dynamics analysis resolved at the formed catalyst shape level of CO2 hydrogenation reactor Reviewed

SHIMADA Taiki, LIN Yixiong, NAKAMURA Maki, NORINAGA Koyo

Proceedings of Conference on Coal Science Vol. 60 ( 0 ) page： 16 - 17 2023.10

Language：Japanese Publishing type：Research paper (scientific journal) Publisher：The Japan Institute of Energy

This paper reports a 3D computational fluid dynamics simulation of carbon dioxide (CO2) methanation in a shell-and-tube reactor resolved to the catalyst geometry level. Fluid flow, heat transfer, and mass transfer are calculated, and the local distribution of gas and solid phases in the reactor is shown in detail. To generalize the simulation model, the catalyst effectiveness factor was treated as a variable, and the catalyst effectiveness factor equation and its parameters were investigated. As a result, the catalyst effective coefficient derived from the general Thiele modulus was the best agreement for the present computational model. For higher accuracy, the equations need to be improved to be more suitable for more reality models and chemical reaction equations.

DOI： 10.20550/jiesekitanronbun.60.0_16

CiNii Research

パティキュラーフィルター用触媒のコンバータモデルの構築 Reviewed

中村真季，横田幸治，岡井健悟, 小澤正邦

自動車技術会論文集 Vol. 54 ( 2 ) page： 242 - 245 2023

Experimental study on quantitative evaluation of transferable hydrogen in possible raw materials for metallurgical cokes including bituminous, sub-bituminous, lignite coals and biomass Reviewed International coauthorship

Lijuan Zhang, Yusuke Uehara, Maki Nakamura, Cheolyong Choi, Chong Liu, Hiroshi Machida, Hideyuki Hayashizaki, Yuya Kawai, Yuki Hata, Koyo Norinaga,

ISIJ International Vol. 63 ( 9 ) page： 1441 - 1450 2023

一次元モデルによる微粒子フィルターのPM堆積・再生シミュレーション-触媒担持位置依存の評価- Reviewed

中村真季，横田幸治，小澤正邦

自動車技術会論文集 2022.9

Numerical Calculation of PM Trapping and Oxidation of Particulate Filter -Considering Operation Mode of the Engine- Reviewed

Maki Nakamura, Koji Yokota, Masakuni Ozawa

Vol. 53 巻 ( 2 号 ) page： 360 - 365 2022.3

Authorship：Lead author Language：Japanese Publishing type：Research paper (scientific journal)

In recent years, emission regulations have become more stringent, and particulate matter (PM) emitted from gasoline engine vehicles is also subject to regulation. PM emitted from a gasoline engine is suppressed by a gasoline particulate filter (GPF). However, unlike diesel engines, exhaust from gasoline engines flows into the GPF under more stringent conditions. Therefore, in this study, we performed numerical calculations based on WLTC, taking into account fluctuations in exhaust gas from gasoline engines, and confirmed the behavior of PM deposition and regeneration.　At that time, the numerical calculation model of the previous research was also improved.　Furthermore, a catalyst was supported on the GPF, and the catalyst performance was evaluated.　As a result, it was suggested that continuous regeneration would be possible by improving the performance of the catalyst.

DOI： https://doi.org/10.11351/jsaeronbun.53.360

Numerical calculation of PM trapping and oxidation of diesel particulate filter – Analysis of PM combustion behavior by a catalyst (Fourth Report) Reviewed

Nakamura Maki, Yokota Koji, Ozawa Masakuni

Transactions of Society of Automotive Engineers of Japan Vol. 52 ( 2 ) page： 257 - 262 2021

Language：Japanese Publishing type：Research paper (scientific journal) Publisher：Society of Automotive Engineers of Japan

The particulate matter (PM) emitted from the diesel engine is collected and removed by the diesel particulate filter (DPF). When performing PM removal, it is necessary to raise the temperature of exhaust gas, so deterioration of fuel efficiency is a serious problem. Therefore, we aim to propose an optimal DPF structure with catalyst addition. In this study, PM combustion behavior inside the DPF when the catalyst is supported is carried out by numerical calculation. As a result, the effectiveness of the catalyst is recognized. It is found that there is a difference in the amount of PM combustion change according to the difference in the activation energy. In this result, it can be suggested that a catalyst having activation energy ΔE = 120 KJ/mol or less is effective. It is also possible to completely remove PM in a single regeneration by using a catalyst with low activation energy or by increasing the exhaust gas temperature. The calculation technique we proposed will enable the qualitative examination of the structure of DPF with catalyst addition, which can be useful for the optimization design of DPF.

DOI： 10.11351/jsaeronbun.52.257

CiNii Research

Mercury Dust Monitor (MDM) Onboard the Mio Orbiter of the BepiColombo Mission

Kobayashi Masanori, Shibata Hiromi, Nogami Ken'ichi, Fujii Masayuki, Hasegawa Sunao, Hirabayashi Masatoshi, Hirai Takayuki, Iwai Takeo, Kimura Hiroshi, Miyachi Takashi, Nakamura Maki, Ohashi Hideo, Sasaki Sho, Takechi Seiji, Yano Hajime, Krueger Harald, Lohse Ann-Kathrin, Srama Ralf, Strub Peter, Grun Eberhard

SPACE SCIENCE REVIEWS Vol. 216 ( 8 ) 2020.12

Acoustic signal production in ethanol by energetic xenon ions Reviewed

Kobayashi Masanori, Miyachi Takashi, Okudaira Osamu, Takechi Seiji, Kurozumi Atsuma, Uno Takefumi, Nakamura Maki, Shibata Hiromi, Okada Nagaya, Fujii Masayuki, Murakami Takeshi, Uchihori Yukio

JAPANESE JOURNAL OF APPLIED PHYSICS Vol. 59 ( 2 ) page： . 2020.2

Soot-combustion catalyst of Pd/ZrO2 composites prepared from Zr65Pd35 amorphous alloy by oxidation treatment Reviewed

Masakuni Ozawa, Atsuhiko Masuda, Maki Nakamura, Masatomo Hattori, Hidemi Kato, Shin-ichi Yamamura

JAPANESE JOURNAL OF APPLIED PHYSICS Vol. 59 ( SA ) 2020.1

Language：English Publishing type：Research paper (scientific journal) Publisher：IOP PUBLISHING LTD

Metal-dispersed Pd/ZrO2 composites were derived from amorphous Zr65Pd35 alloy and their catalytic behavior for diesel soot combustion was studied. X-ray diffractograms and scanning electron micrographs indicated that mixtures of ZrO2 phase and the dispersed metallic phase were formed in the resulting material after heat treatment at 800 degrees C in air. The oxidized alloy resulted in the enhanced soot combustion activity. The removal property of catalyst, evaluated as temperature, is almost 100 degrees C better than that in the non-catalyzed reaction. The combustion processes were observed by in situ high temperature optical microscopy (HTOM) and ex situ electron microscopy with different scales. The secondary soot particle started the combustion at the primary soot near catalyst. Upon heating to higher temperature between 570 degrees C and 590 degrees C the soot layer rapidly disappeared in in situ HTOM, while both the black band and dispersed part of soot on a alumina substrate remained without combustion even kept at 650 degrees C. Therefore, soot did not move with micron-order distance and its combustion process should depend on their contact points of catalyst surfaces and soot aggregate. This work provided a new type of catalytic material prepared from amorphous alloys which was effective soot combustion catalysis. (c) 2019 The Japan Society of Applied Physics

DOI： 10.7567/1347-4065/ab45fb

Web of Science

Scopus

Numerical Calculation of PM Trapping and Oxidation of Diesel Particulate Filter with Catalyst Reviewed

Maki Nakamura, Koji Yokota, Masatomo Hattori and Masakuni Ozawa

SAE Technical paper page： 2020-01-2169 2020

Numerical Calculation of PM Trapping and Oxidation of Diesel Particulate Filter -Parametric Studies of DPF Form Dependence (Third Report) Reviewed

Yokota Koji, Nakamura Maki, Hattori Masatomo, Ozawa Masakuni

Transactions of Society of Automotive Engineers of Japan Vol. 51 ( 5 ) page： 882 - 887 2020

Language：Japanese Publishing type：Research paper (scientific journal) Publisher：Society of Automotive Engineers of Japan

The particulate matter (PM) emitted from the diesel engine is collected and removed by the diesel particulate filter (DPF). When performing PM removal, it is necessary to raise the temperature of exhaust gas, so deterioration of fuel efficiency is a serious problem. Therefore, we aim to propose an optimal DPF structure. In this study, we confirmed the dependence of the shape of the DPF during PM deposition-regeneration process using a numerical calculation. The quick change of the pressure drop and the amount of combustion of PM is smaller when the length of the DPF becomes larger. When the DPF length is long, the residual of PM amount at the outlet of DPF decreases. And the PM on the whole surface burns. When the after 10－15 deposition combustion repetitions, the amount of change of PM shows the same pattern. This model can be used for the optimal design of catalytic DPFs by assuming some modes of operation of the DPF device before the experimental approach.

DOI： 10.11351/jsaeronbun.51.882

CiNii Research

PM Trapping and Oxidation in Diesel Particulate Filter with Catalyst by Numerical Calculation of One-dimensional Model Reviewed

Nakamura Maki, Yokota Koji, Ozawa Masakuni

Transactions of Society of Automotive Engineers of Japan Vol. 51 ( 2 ) page： 238 - 243 2020

Authorship：Lead author,　Corresponding author Language：Japanese Publishing type：Research paper (scientific journal) Publisher：Society of Automotive Engineers of Japan

In this study, we proposed a numerical method to estimate the behavior of PM distribution in DPF both in PM-deposition and regeneration process. In the result, we found that PM oxidation was occasionally incomplete and partially remained in the DPF even if the PM deposition-regeneration process was repeated in the DPF. In such case, the phenomenon that the oxygen supply slightly decreased towards the rear part of the DPF was found, so that the remained PM in the DPF induced the new PM deposition. By using a novel model, PM deposition distribution and modeling of the oxidization reaction, where deposition-regeneration is especially repeated within DPF, could be performed and time-dependent behavior of pressure loss was considered. The present modeling will make possible suggest the required timing which performs compulsive reproduction control of DPF.

DOI： 10.11351/jsaeronbun.51.238

CiNii Research

Numerical Calculation of PM Trapping and Oxidation of Diesel Particulate Filter – Thermal Analysis in the DPF (Second Report) Reviewed

Nakamura Maki, Yokota Koji, Hattori Masatomo, Ozawa Masakuni

Transactions of Society of Automotive Engineers of Japan Vol. 51 ( 2 ) page： 274 - 279 2020

Authorship：Lead author,　Corresponding author Language：Japanese Publishing type：Research paper (scientific journal) Publisher：Society of Automotive Engineers of Japan

The particulate matter (PM) discharged from the diesel engine is collected by a diesel particulate filter (DPF) and then removed. Deterioration of fuel consumption is a serious problem since exhaust gas temperature must be increased when PM removal is performed. In this study, the numerical computation for both the behavior of PM distribution in the DPF during PM deposition-regeneration process and the heat distribution in the DPF was performed. The temperature-distribution and its change in DPF as a function of the time during PM combustion were calculated by a newly developed model. It was concluded that the amount of increasing temperature change was far larger backside in direction than that near the entrance of an inflow way. The present model can be used for optimal designing of DPF with a catalyst by assuming several operation modes of DPF device before an experimental approach.

DOI： 10.11351/jsaeronbun.51.274

1次元モデルによる触媒付ディーゼル微粒子フィルターのPM堆積・酸化シミュレーション-DPF形状依存性（第三報） Reviewed

横田幸治, 中村真季, 小澤正邦

自動車技術会論文集 Vol. 51 ( 5 ) page： 882 - 887 2020

Phenomena of PM deposition and oxidation in the diesel particulate filter Reviewed

Maki Nakamura, Masakuni Ozawa

SAE Technical paper 2019

Effect of Surface Cavity Shape on PM Deposition and Pressure Drop in DPF Porous Material Reviewed

NAKAMURA Maki, OZAWA Masakuni

Journal of the Society of Materials Science, Japan Vol. 67 ( 5 ) page： 562 - 567 2018

Authorship：Lead author Language：Japanese Publishing type：Research paper (scientific journal) Publisher：The Society of Materials Science, Japan

The diesel particulate filter (DPF) has attracted strong attention as a desirable after-treatment device for the particulate matter(PM) contained in exhaust gas of diesel engine. When particulate matter was deposited on a DPF, the pressure drop increases due to the PM trapping in the surface cavities of the DPF. In this study, we compared the dependence of the shape and depth of the pore of the DPF on the PM trapping process by total model and numerical calculation. We found that the pressure drop and elapsed time of the PM trapping varied, significantly depending on the pore shape of the DPF surface. Further we examined the relative importance of the amount of PM deposit and the surface cavity shape of the DPF, and found that the pressure drop was lower when the shape of surface cavity in DPF became flatter and shallower. The result provides a quantitative evaluation and design of the surface cavity in the DPF leading to better production process of porous ceramic parts.

DOI： 10.2472/jsms.67.562

Scopus

CiNii Books

Development of in-situ micro-debris measurement system Reviewed

Nakamura M.

Advances in Space Research Vol. 56 ( 3 ) page： 436 - 448 2015.8

Numerical Simulation of Trapping Process in Hexagonal Diesel Particulate Filters Reviewed

Nakamura Maki, Hanamura Katsunori, Shibuta Takumi, Yoshino Hajime, Iwasaki Kentaro

Transactions of Society of Automotive Engineers of Japan Vol. 46 ( 2 ) page： 313 - 317 2015.3

Authorship：Lead author Language：Japanese Publishing type：Research paper (scientific journal) Publisher：Society of Automotive Engineers of Japan

The process of soot trapping in a hexagonal cell geometry diesel particulate filters (HEX DPF) in surface pores filtration made of aluminum titanium oxide were investigated through a simple analysis based on Darcy's law through the wall and deposited soot layer. In this study, we focused on the trapping process of the HEX DPF cell in surface pores filtration by Numerical Simulation. The HEX DPF had two types of flow: one was a flow through a wall between inlet and outlet channels (inlet/outlet wall flow), and the other was a flow which was introduced into a wall between inlet and inlet channels, and was turned toward the direction parallel to the wall, and finally exited into the outlet channel (bypass flow). As a result, the process of soot trapping in surface pores filtration was shown by numerical simulation. It was possible to express the transition process from surface pores filtration to cake filtration.

DOI： 10.11351/jsaeronbun.46.313

CiNii Books

Flow Analysis during Soot Trapping on Aluminum Titanate Ceramics Filter with Hexagonal Cell Geometry Reviewed

Maki NAKAMURA, Katsunori Hanamura, Takumi Shibuta, Kentaro Iwasaki, Hajime Yoshino

International Journal of Automotive Engineering (IJAE) Vol. 6 ( 1 ) page： 31-37 2015

Authorship：Lead author Language：English Publishing type：Research paper (scientific journal)

The phenomena of soot trapping and oxidation in a hexagonal cell geometry DPF made of aluminum titanium oxide were investigated through microscopic visualization experiment and a simple analysis based on Darcy's law through the wall and the deposited soot layer. There were two types of flow: one was a flow through a wall between inlet and outlet channels (inlet/outlet wall flow), and the other was a flow which was introduced into a wall between inlet and inlet channels, and was turned toward the direction parallel to the wall, and finally exited into the outlet channel (bypass flow). The flow rate of the bypass flow was increased with a thickness of soot layer deposited on the inlet/outlet wall. As a result, the soot was trapped even on the inlet/inlet wall surface. In the regeneration process, depending on the flow rate of the bypass flow, the maximum temperature for the hexagonal cell DPF became lower compared with that for the conventional DPF.

DOI： https://doi.org/10.20485/jsaeijae.6.1_31

Variation in resonant frequency of piezoelectric lead-zirconate-titanate element undergoing high-level radiation Reviewed

Masanori Kobayashi, Takashi Miyachi, Seiji Takechi, Tomoaki Mitsuhashi, Yoshinori Miura, Hiromi Shibata, Nagaya Okada, Maki Hattori, Osamu Okudaira, Masayuki Fujii, Takeshi Murakami, Yukio Uchihori

JAPANESE JOURNAL OF APPLIED PHYSICS Vol. 53 ( 6 ) 2014.6

Language：English Publishing type：Research paper (scientific journal) Publisher：IOP PUBLISHING LTD

A piezoelectric lead-zirconate-titanate (PZT) element was exposed to a 400MeV/n xenon beam and the radiation effect on the element was studied as a variation of resonant and antiresonant frequencies by the resonance method. A possible effect of heating the element on the resonant frequency was avoided by using data obtained while the temperature of the element was kept constant. Consequently, the variation of the resonant frequency was empirically represented by a simple function of the amount of accumulated energy in the element. We therefore discuss the piezoelectric PZT element as a potential detector for high-level radiation. We point out that a piezoelectric equation including the heat term is required to explain the experimental results. (C) 2014 The Japan Society of Applied Physics

DOI： 10.7567/JJAP.53.066602

Web of Science

Output characteristics of piezoelectric lead zirconate titanate detector using high-energy heavy-ion beam Reviewed

Seiji Takechi, Masahiro Sekiguchi, Takashi Miyachi, Masanori Kobayashi, Maki Hattori, Osamu Okudaira, Hiromi Shibata, Masayuki Fujii, Nagaya Okada, Takeshi Murakami, Yukio Uchihori

NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION A-ACCELERATORS SPECTROMETERS DETECTORS AND ASSOCIATED EQUIPMENT Vol. 737 page： 52 - 55 2014.2

Language：English Publishing type：Research paper (scientific journal) Publisher：ELSEVIER SCIENCE BV

A radiation detector fabricated using piezoelectric lead zirconate titanate (PZT) has been studied by irradiating it with a 400 MeV/n xenon (Xe) beam. The beam diameter was controlled to change the irradiation conditions. It was found that the magnitude of the output observed from the PZT detector may be related to the number of Xe ions per unit area per unit time within the limits of the experimental conditions. (C) 2013 Elsevier B.V. All rights reserved

DOI： 10.1016/j.nima.2013.11.029

Web of Science

Study of Deterioration in a Piezoelectric Lead Zirconate Titanate Radiation Detector through Measurement of the Electromechanical Coupling Factor with 400 MeV/n Zenon Ions Reviewed

Masanori Kobayashi, Takashi Miyachi, Seiji Takechi, Masahiro Sekiguchi, Hiromi Shibata, Nagaya Okada, Maki Hattori, Osamu Okudaira, Masayuki Fujii, Takeshi Murakami, Yukio Uchihori

JAPANESE JOURNAL OF APPLIED PHYSICS Vol. 52 ( 12 ) 2013.12

Language：English Publishing type：Research paper (scientific journal) Publisher：IOP PUBLISHING LTD

The variation of the electromechanical coupling factor (ECF) was measured by bombarding a piezoelectric lead zirconate titanate (PZT) element with 400 MeV/n xenon ions. The element was exposed to energies up to 10(4) J, during which time the ECF was observed by the resonance method. The ECF gradually decreased with the energy accumulated during irradiation, and its behavior was scaled with an empirical formula. This decrease suggests that the piezoelectric quality deteriorated; hence, the sensitivity of the PZT radiation detector was considered to be degraded as well. The variation ultimately originated in resonance-associated processes. A potential detector suitable for use in severe-radiation environments was discussed. (C) 2013 The Japan Society of Applied Physics

DOI： 10.7567/JJAP.52.126604

Web of Science

Dust detector using piezoelectric lead zirconate titanate with current-to-voltage converting amplifier for functional advancement Reviewed

Kobayashi, Masanori ; Miyachi, Takashi ; Hattori, Maki ; Sugita, Seiji ; Takechi, Seiji ; Okada, Nagaya

Earth, Planets and Space 2013.3

Influence of a Polyimide Surface Layer on the Piezoelectric Response of Lead-Zirconate-Titanate Cosmic Dust Detector Reviewed

Maki Hattori, Masanori Kobayashi, Takashi Miyachi, Seiji Takechi, Osamu Okudaira, Takeo Iwai, Nagaya Okada, Seiji Sugita

JAPANESE JOURNAL OF APPLIED PHYSICS Vol. 52 ( 2 ) 2013.2

Language：English Publishing type：Research paper (scientific journal) Publisher：IOP PUBLISHING LTD

The influence of a thermal reflector on the sensitivity of a lead-zirconate-titanate element is studied by bombarding the element with hypervelocity microparticles. The reflector is a 60-mu m-thick layer made of polyimide resin that coats the surface of the element. By applying the fast Fourier transform method to data analysis, impact information is obtained through the fundamental resonant component. As a result, the sensitivity of the element is considerably reduced by the reflector. In addition, it is found that the sensitivity is substantially position-independent. (C) 2013 The Japan Society of Applied Physics

DOI： 10.7567/JJAP.52.028002

Web of Science

Position-Dependent Behavior of Piezoelectric Lead-Zirconate-Titanate Cosmic Dust Detector Reviewed

Maki Hattori, Masanori Kobayashi, Takashi Miyachi, Seiji Takechi, Osamu Okudaira, Takeo Iwai, Seiji Sugita

JAPANESE JOURNAL OF APPLIED PHYSICS Vol. 51 ( 9 ) 2012.9

Language：English Publishing type：Research paper (scientific journal) Publisher：JAPAN SOC APPLIED PHYSICS

A possible position dependence of the signal amplitudes generated by a piezoelectric lead-zirconate-titanate (PZT) detector was studied by bombarding the PZT element with hypervelocity microparticles. The detector was equipped with a set of asymmetrically arranged electrodes. The characteristic features of the element were analyzed using the amplitudes of the fundamental resonant component caused by collisions. As a result, the sensitivity of the element measured with direct collisions onto the collector was found to be one order of magnitude greater than that in the external area of the collector. (C) 2012 The Japan Society of Applied Physics

DOI： 10.1143/JJAP.51.098004

Web of Science

Laboratory experiments on crater scaling-law for sedimentary rocks in the strength regime Reviewed

22) Suzuki, A., S. Hakura, T. Hamura, M. Hattori, R. Hayama, T. Ikeda, H. Kusuno, H. Kuwahara, Y. Muto, K. Nagaki, R. Niimi, Y. Ogata, T. Okamoto, T. Sasamori, C. Sekigawa, T. Yoshihara, S. Hasegawa, K. Kurosawa, T. Kadono, A. M. Nakamura, S. Sugita, and M. Arakawa

2012.8

A future observational plan of dust particles around the Moon by LDM (Lunar Dust Monitor) onboard the orbiter of the next Japanese lunar mission

Kobayashi Masanori, Ohashi Hideo, Sasaki Sho, SHIBATA Hiromi, IWAI Takeo, FUJII Masayuki, NOGAMI Ken-ichi, KIMURA Hiroshi, NAKAMURA Maki H., HIRAI Takayuki, SRAMA Ralf, GRUN Eberhard

Earth, planets and space Vol. 63 ( 10 ) page： 1113-1117 2011.10

A future observational plan of dust particles around the Moon by LDM (Lunar Dust Monitor) onboard the orbiter of the next Japanese lunar mission Reviewed

Kobayashi, M; Ohashi, H; Sasaki, S; Shibata, H; Iwai, T; Fujii, M; Nogami, K; Kimura, H; Nakamura, MH; Hirai, T; Srama, R; Grün, E

EARTH PLANETS AND SPACE Vol. 63 ( 10 ) page： 1113 - 1117 2011

Effect of Heating and Cooling on the Piezoelectric Properties of a PZT Sensor for Mercury Dust Monitor Reviewed

24) Takeo IWAI, Maki NAKAMURA, Hideo OHASHI, Hiromi SHIBATA, Takashi MIYACHI, Seiji TAKECHI, Hajime YANO, Sho SASAKI, Masayuki FUJII, Ken-ichi NOGAMI, Eberhard GRÜN and Ralf SRAMA

Trans. JSASS Aerospace Tech. Japan 2010

　 PREV - NEXT 　

<NAKAMURA Maki>

Papers - NAKAMURA Maki