Papers - KOBASHI, Makoto
-
板状ポーラスアルミニウムの発泡特性と気孔性状に及ぼす板厚拘束の影響 Reviewed
小橋 眞,坂本憲昭,金武直幸
軽金属 Vol. 58 ( 12 ) page： 7-12 2009.1
-
圧縮ねじり加工したAZ61マグネシウム合金の微視組織に及ぼす回転回数の影響 Reviewed
筒井一輝久米裕二小橋 眞金武直幸
日本塑性加工学会誌 Vol. 51 ( 588 ) page： 38-42 2009
-
*燃焼合成法による超微細TiB2粒子生成過程の観察と微細化手法の検討 Invited Reviewed
小橋 眞吉田 亘金武直幸
軽金属 Vol. 58 ( 10 ) page： 491-496 2008.10
-
Foaming behavior of aluminum precursor produced from machined chip waste Reviewed
N. Kanetake, M. Kobashi
( 10 ) page： 840-844 2008.10
-
*Reactive infiltration of TiN powder preform with molten Al for the fabrication of nitride ceramics composite Invited Reviewed
Y. KobayashiM.KobashiN. Kanetake
Mater. Trans Vol. 49 ( 7 ) page： 1616-1620 2008.7
-
*プリカーサ法によるポーラスアルミニウム充填構造体のプロセス技術 Invited Reviewed
小橋 眞金武直幸
まてりあ Vol. 47 ( 04 ) page： 178-181 2008.4
-
燃焼合成法による中空パイプ/Al3Niフォーム複合構造体の作製と気孔性状の解析 Invited Reviewed
小橋 眞、金武直幸
高温学会誌 Vol. 34 ( 2 ) page： 79-84 2008.2
-
燃焼合成法によるポーラス材料の開発 Reviewed
金武直幸、小橋 眞
高温学会誌 Vol. 34 ( 02 ) page： 45-50 2008.2
-
圧縮ねじり加工法による微細化組織の分布に及ぼすねじり負荷条件の影響 Reviewed
久米裕二 小橋 眞 金武直幸
日本塑性加工学会誌 Vol. 49 ( 1 ) page： 51-55 2008.1
-
Tensile Property of Hypereutectic Al-Si Alloy Re-fined by Compressive Torsion Processing
Y. Kume, S. Tahara, M. Kobashi, N. Kanetake
Vol. 1 page： 589-594 2008
-
Solid State Recycling of Aluminum Machined Chip Wastes by Compressive Torsion Processing
N. Kanetake, M.Kobashi, Y.Kume
Aluminium Alloys: Their Physical and Mechanical Properties Vol. 1 page： 541-546 2008
-
圧縮ねじり加工法による結晶粒微細化に及ぼす加工温度と試料直径の影響 Reviewed
久米裕二小橋 眞金武直幸
日本塑性加工学会誌 Vol. 48 ( 11 ) page： 1007-1011 2007.11
-
Synthesis of Fine Ceramic Particles in Molten Aluminum by Combustion Reaction Reviewed
W. Yoshida M.Kobashi N. Kanetake
Mater. Trans. Vol. 48 ( 9 ) page： 2374-2377 2007.9
-
Novel Processing of Porous Titanium Composite for Producing Open Cell Structure Reviewed
M. KobashiN. Kanetake
Vol. 26-28 page： 133-136 2007
-
Fabrication of Long Scale Aluminum Foam By Transfer Heat Foaming of Precursor Reviewed
Fabrication of Long Scale Aluminum Foam By Transfer Heat Foaming of Precursor
E. MizutaniM. KobashiN. Kanetake Vol. 909-912 page： 2007 2007
-
Fabrication of Magnesium Foam by Precursor Method Using Machined Chips Reviewed
K. MaeharaM. KobashiN. Kanetake
Advanced Materials Research Vol. 26-28 page： 905-908 2007
-
Effect of Powder Blending Ratio on Synthesis of TiB2 Particles by Al-Ti-B Combustion Reaction Reviewed
W. YoshidaM. KobashiN. Kanetake
Advanced Materials Research Vol. 26-28 page： 325-328 2007
-
Fabrication of Oxide Ceramics Composite by Reactive Infiltration Process Reviewed
Y. KobayashiM. KobashiN. KanetakeW. YoshidaM. KobashiN. Kanetake
Advanced Materials Research Vol. 26-28 page： 321-324 2007
-
Influence of Compressive Torsion Processing Temperature Microstructure Refinement and Property of Aluminum alloy Reviewed
S.TaharaY. KumeM. KobashiN. Kanetake
Advanced Materials Research Vol. 26-28 page： 321-324 2007
-
Homogeneity of Grain Refinement of Aluminum Alloy with Compressive Torsion Processing Reviewed
Y. KumeM. KobashiN. Kanetake
Advanced Materials Research Vol. 26-28 page： 107-110 2007